1. A thin-walled cylinder with a diameter of 20 cm and a wall thickness of 2 mm is filled with gas at a pressure of 2 MPa. Calculate the longitudinal stress, and circumferential stress in the cylinder wall.

1. A thin-walled cylinder with a diameter of 20 cm and a wall thickness of 2 mm is filled with gas at a pressure of 2 MPa. Calculate the longitudinal stress, and circumferential stress in the cylinder wall.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.7P: A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the...

See similar textbooks

Related questions

Q: and 2.5cm in diameter, determine (a) the rate of heat transfer and (b) the outlet temperatures of…

A: To calculate the rate of heat transfer, and outlet temperature of the glycerine and glycolgiven the…

Q: Consider a U-tube manometer used to measure the density pa of liquid A, as shown below. Mercury is…

Q: The mechanism shown in (Figure 1) is used in a riveting machine. It consists of a driving piston A,…

A: The mechanism shown in (Figure 1) is used in a riveting machine. It consists of a driving piston A,…

Q: A 1000 kg automobile accelerates from 10 km/hr to 120 km/hr. How much work does this require?

A: Question(4)Given:Mass Initial Velocity Final Velocity To find:The required Work

Q: Describe the steps involved in creating a mathematical model for a mechanical system.

Q: Ammonia enters the expansion valve of a refrigeration system at a pressure of 10 bar and a…

A: The inlet pressure at the inlet of expansion valve is The inlet temperature at the inlet of…

Q: You have been asked to evaluate the economic implications of various methods for cooling condenser…

Q: Problem 2 – Control volume compressor analysis An adiabatic compressor used in a refrigeration…

A: To answer these questions, we'll use the properties of R-134a from a refrigerant table (you can find…

Q: What are the key challenges and trends in microchip design and fabrication as we move towards…

A: To explain:the key challenges and trends in microchip design and fabrication.

Q: A steady-flow, well-insulated turbine accepts steam at 4 MPa and 500°C with negligible kinetic and…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Following is tabulated data that were gathered from a series of Charpy impact tests on a tempered…

A: Given:To find:

Q: A wave with the following deep water characteristics is propagating toward the coast: Ho=1 m T=15 s…

A: Initial wave height, Ho =1 mwave period, T = 15 secondsdepth, d = 5 m

Q: The figure shows a frame with negligible mass, keeping a 50-lb weight in equilibrium. The smooth…

Q: Which one of the following materials would plastic deformation through twinning be the most likely…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A stepped cylinder has the dimensions R₁ = 0.30 m, R₂ = 0.65 m, and the radius of gyration, k, is…

A: The inner radius is .The outer radius is .The radius of gyration of cylinder is .The mass of…

Q: For the beam ABC loaded as shown below, (a) draw the shear force and bending moment diagrams, and…

A: For the beam ABC loaded as shown below, (a) draw the shear force and bending moment diagrams, and(b)…

Q: Bar BC weighs 161 lb and has a radius of gyration of mass with respect to a hor- izontal axis…

Q: Problem 16.110 Figure 0.6 m 0.3 m B -0.6 m DE aCD WCD ▼ Part A QAB= Submit Determine the angular…

Q: A spherical tank,the inner diameter 50 cm and is maintained at temperature of 50c,the outer…

Q: Given the T-s diagram of the vapor compression refrigeration cycle with 0.09 kg/s of refrigerant…

Q: Problem 1. A hockey puck having a mass of 0.25 kg slides on the frictionless horizontal surface of a…

A: Given:To find:(a) Determine the x and y components of the force F1 = 5 N and F2 = 9 N.(b) Determine…

Q: The 12-ft boom AB has a fixed end A. A steel cable is stretched from the free end B of the boom to a…

A: Here we will first get the position vectors and use the moment equation

Q: Draw the Shear and Moment Diagrams for the beam shown. The beam has a 30 kNm moment applied at x=0 m…

A: Draw the Shear and Moment Diagrams for the beam shown.The beam has a 30 kNm moment applied at x=0 m…

Q: 1-32. Determine the largest intensity w of the uniform loading that can be applied to the frame…

A: For the solution refer below images.

Q: The collar C in Fig. 16-16a is moving downward with a velocity of 2 m/s. Determine the angular…

A: The collar C in Fig. 16-16a is moving downward with a velocity of 2 m/s. Determine the angular…

Q: Discuss the concept of hybrid systems and the modeling approaches used to address systems with both…

A: This question is based on the concept of hybrid system and modelling approach used.

Q: O lit/sec water enters a centr ally at 5 m/s and leaves at a - axial direction. If the inlet

Q: The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating…

A: For the solution refer below images.

Q: An air standard Otto cycle is has a compression ratio of 7. At the beginning of the compression,…

A: The compression ratio of otto cycle is .The initial pressure is .The initial temperature is .The…

Q: 3. The temperature inside a Carnot refrigerator is maintained at 5°C by rejecting heat to the…

Q: Consider the truss shown in the figure, built from three struts attached by three pins. The truss…

A: Consider the truss shown in the figure, built from three struts attached by three pins. The truss…

Q: Most gasoline engines in today's automobiles are belt driven. This means that the crankshaft, a rod…

A: The speed of smaller crankshaft is .The radius of smaller crankshaft is .The radius of larger…

Q: Write an essay with diagrams discussing stress, strain, in brass, also, discuss a material that is…

A: This question is based on the concept of stress-strain of brass.

Q: Find the toughness for a metal that experience valid for elastic deformation, that the modulu…

A: Given Modulus of Elasticity, E = 103 GPa K = 1520 MPa…

Q: In this system, there are two mass elements: m, and m₂. They are con- nected by a spring. m₁ is also…

Q: 3. The compound beam given in the figure is composed of a pair of beams, AB and BC, connected by a…

A: The compound beam given in the figure is composed of a pair of beams, AB and BC, connected by a pin…

Q: Determine the force in member BE of loaded truss. (Use method of sections) 6kN D

A: The truss system is given by.Determine the force in member BE.

Q: The figure shows a cantilevered beam, subjected to a uniformly distributed (rectangular) 40 N/m…

Q: Data: r=0.25 inch, d=0.4 pig and h=0.5 inch, wi=2.5 inch and w= 1.5 inch. The forces fluctuate…

A: Where:Force = 14 Kips (tension) = 14,000 lbsForce = 5 Kips (compression) = -5,000 lbs (negative sign…

Q: The onset of free convection. Plastic shrink wrap can be used to insulate windows by trapping air…

Q: and indicate, with arrows, the directions of working fluid flow. b. Determine the required operating…

A: To draw temperature entropy drawing R 22 fluid, to calculate operating pressures and quality at…

Q: B 20° 30Р

A: Calculate acceleration of Bmass of block A mass of block B and the angles

Q: One kilogram on a diatomic ideal gas undergoes the following four step process starting at Point A…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: The ideal spring of constant k-2.6 kN/m is attached to the disk at point A and the end fitting at…

A: The moment about the z axis of the spring force is .The spring constant is

Q: For an ideal, regenerative Rankine cycle utilizing steam as the working fluid, water enters the…

Q: Required information A gas is compressed from an initial volume of 0.42 m³ to a final volume of 0.12…

Q: The magnitude of the absolute velocity of point A on the automobile tire is 19.6 m/s when A is in…

Q: A Lassonde Startup Company aims to expand its pump business into rural areas, where accessing clean…

Q: 6.2 Isobaric Cooling and Condensation of R134a 2 kg of superheated R134a at p₁ = 1 MPa, T₁ = 70°C…

A: The mass of superheated R134a is .The initial pressure is .The initial temperature is .The state 2…

Q: 4/36 Determine the force in member BE of the loaded truss.

A: Here we will use the method of section to calculate the load in member BE

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given and required

VIEW

Step 2: Determination of stress

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 10 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. A thin-walled sphere with a diameter of 30 cm and a wall thickness of 3 mm is filled with liquid at a pressure of 3 MPa. Calculate the stress in the sphere wall.
A steel cylindrical pressure vessel with closed ends is 25 cm external diameter and 5 mm thick It is wound closely with a single layer of circular wire of diameter 1.2 mm. Under the tension of 96 N/mm'. If the cylinder is treated as thin. Calculate (1) Initial stress in cylinder. (ii) Initizl pressure which will produce a stress of 48 N/mm2.
Pressure inside the cylinder is 10 bars Is this a thin walled cylinder when the thickness is 10 mm. Estimate theoretically the hoop andlongitudinal stresses
A gas is stored in a cylindrical tank of inner radius 7 m and wall thickness 50 mm. The gage pressure of the gas is 2 MPa. The maximum shear stress (in MPa) in the wall is
Find the stress acting on the surface of a thin sphere of diameter 15 cm, thickness 0.25 cm and the internal pressure is 2 MPa
b) For the thin walled pressure vessel subjected to an internal pressure of 150 psi and as shown below, calculate the longitudinal and transverse stresses. Assume length as L ft and 1 in. wall thickness as 8 2 ft E2.5 ft -d Type your answer in the Word format here Page 2 of 2 565 words Search
A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is 1 m long. It is found to change in internal volume by 12.0 x 10-6 m3 when filled with a liquid at a pressure p. If E = 200GN/m2 and v = 0.25, and assuming rigid end plates, determine the values of hoop stress
A rectangular plate, 30mm by 60 mm is subjected to a tensile force of 5kN in the direction of the plate’s larger side. The plate has a circular hole at the center with diameter of 15mm. If stress concentration factor=2.16, find the thickness of the plate if maximum allowable tensile stress is 80N/mm².
A thin cylindrical vessel of 2 m diameter contains a particular gas at a pressure of 1.65 MPA. If the permissible tensile stress of the material of the shell is 150 MPa, find the minimum thickness required.
A water reservoir of 24 m high and 12 m in diameter is to be completely filled with water, find the minimum thickness of the reservoir plating if the stress is limited to 50 MPa.
A thick-walled cylinder has an outer and inner diameter of 200 and 50 mm, respectively. The cylinder is designed to store fluid at 80 MPa:(a) Determine the external pressure necessary to bring the hoop stress at the outer wall of the cylinder to zero. (b) Draw the variations of the hoop and radial stress across the thickness of the wall. Indicate the stress values at both inner and outer radii.
Engineer firms in many situations must verify the reliability of existing purchased designs. Your role as a quality engineer at an oil refinery is to confirm the maximum stresses imposed by a 1.03 MPa propane pressure inside the 20-lb design cylinder shown in Figure.3(a), at 25°C, which acts as a pressurized cylinder once the gate valve is closed. If the cylinder is made of 2.5-mm-thick steel and can be approximated as shown in Figure.3(c). Evaluate the maximum longitudinal and hoop stresses. 308 mm OL H 447 mm B (b)