es 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 KJ/kg, if cooling water passes through the condenser with temperature increases from 13oC to 24oC. Calculate the cooling water flow rate in kg/sec.

es 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 KJ/kg, if cooling water passes through the condenser with temperature increases from 13oC to 24oC. Calculate the cooling water flow rate in kg/sec.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Related questions

Q: Question attached

A: Given, The mass flow rate of the steam, ms˙=3 kg/s The dryness fraction at the inlet, x=0.8 The…

Q: 1. Helium expands polytropically through a turbine according to the process pv15 =C. The inlet…

Q: condenser with an enthalpy of 2503 kJ/kg and The condensate leaves the condenser 2 Steam enters a a…

A: Given data At inlet of condenser enthalpy of steam (h1) = 2503 kJ/kg velocity of steam (V1) = 74…

Q: a power plant steam, steam is continuously extractedfromthe turbine and in a heat exchanger there is…

A: Data given- Q1 = 1200 kJ/hr Q2 =800 kJ/hr T1 = 20°C = 293 K

Q: Water vapor with a flow rate of 20000 kg / h enters the condenser of a power plant at a pressure of…

Q: rh not O Trot = 75°C %3D Tout-? hcold O Teota = 18°C %3D Hot and cold stream of water are mixing…

Q: A 3.19 kg/s of oxygen gas enters a compressor with the shown conditions and then enters the heat…

Q: Water vapor with a flow rate of 20000 kg / h enters the condenser of a power plant at a pressure of…

Q: A 112 tons of refrigeration system is used to produce chilled water from 22 °C to 2°C. compute the…

A: given capacity of the refrigeration system =112toninitial water temperature T1=22oCfinal water…

Q: An adiabatic feed pump in a steam cycle delivers water to the steam generator at a temperature of…

Q: The air considered as the ideal gas flows through the compressor and heat exchanger at a volumetric…

Q: SOLVE THE PROBLEM AND SHOW THE DETAILED SOLUTION A steam condenser receives 10 kg per second of…

A: To Find : The cooling water flow rate. Given : The mass flow rate is m˙s=10 kgs. The enthalpy of…

Q: 2 m^3/min of a light oil are to be heated from 20C to 100C (with zero vaporization) in an exchanger…

Q: 1.4 A steam turbine is operating at a steam flow rate of 550 kg/s with an enthalpy of live steam h,…

Q: 0.2 A condenser condenses 2700kg steam per hour while air leaks into It at 2.2kg/hr. The condensate…

A: Given: The steam condenses per hour, mw = 2700 kg/hour The air leakage into the condenser, ma = 2.2…

Q: An R-22 compressor has a 5 percent clearance volume and a displacement rate of 80 L/s and pumps…

A: given R-22 working fluid C = 5%, Q = 80 L/s Tlow = -10o c , Thigh = 40o c

Q: Water vapor with a flow rate of 20000 kg / h enters the condenser of a power plant at a pressure of…

Q: Air at 32℃ DBT and 20℃ WBT is passed through a cooling coil maintained at 5℃. The heat extracted by…

Q: Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of…

Q: Used to cool the cockpit of a refrigerated aircraft (33 tons of simple air refrigeration). The…

Q: 1. Using the Steam Tables, determine the heat absorbed by the boiler (KW) and Wsf when subcooled…

A: Stating that as per our guidelines we are supposed to answer?️ only one question. Kindly repost…

Q: Steam enters the condenser of a steam power plant at 30 kPa, a quality of 91 % and a mass flow rate…

A: . .

Q: Water flows inside a heat exchanger, where it gains heat. The diameter at the inlet is 50 mm with a…

A: The diameter of the heat exchanger is, d=50 mm. The velocity of the water is, v=2 m/s. The inlet…

Q: Part C A surface condenser is required to condense 30,000 kg of dry steam per hour at a pressure of…

A: Given, Mass flow rate of steam, ms = 30000 Kg/hr = 8.33 kg/s Pressure and temperature of steam ,…

Q: Steam is supplied to a fully loaded 100-hp turbine at 175 psia with u =1,100.0 Btu/Ibm: Vy=2.00…

A: u1=1100 Btu/lbm,Vy=2 ft3/lbm,V1=400 fpsu2=265 ft3/lbm,v2=1140 fps,Q=-11 Btu/lbm, Applying steady…

Q: A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses…

Q: Steam enters the condenser of a steam power plant at a flow rate of 18000 kg/h, a degree of dryness…

A: Mass flow rate of steam, m˙s=18000kg/h=180003600kg/s=5kg/s Degree if dryness of steam at inlet,…

Q: A heat exchanger is used to cool the water that enters at 100 kPa, 400 at rate of 5 kg/s. The water…

A: Solution: a) Since water exits as saturated vapour from the heat exchanger saturation temperature at…

Q: refrigeration in kW. The specif

Q: For the production of high-speed trains at the SIEMENS company in Krefeld, considerable amounts of…

Q: For an exhaust valve, the mass flow rate through the valve is 1.26 kg/s. The flow coefficient is…

Q: ) A pump in a municipality's water-supply system receives water from the filtration beds and pumps…

Q: () What increase in entropy (in 3/K) is produced by mixing 30.0 kg of 86.5C water with 30.0 kg of…

A: (c)

Q: A water tube boiler has a capacity of 1000 kg/hr of steam. The factor of evaporation is 1.3, boiler…

A: Given:- Total coal=50000kg Factor=1.3 Capacity=1000 kh/hr Boiler efficiency=5% Heating surface area=…

Q: Q.2: A refrigeration system using refrigerant 22 is to have a refrigerating capacity of 80 kW. The…

A: Refrigerant=R22Refrigerating capacity, Q˙e=80 kWEvaporating temperature, Te=-8oCCondensing…

Q: Superheated steam at a pressure of 40 bar and a temperature of 500 0C enters a steam turbine. The…

A: Given:P1=40 barT1=500 °CP2=0.2 barx=0.85m=150000 Kg/hrheat loss=800 KW

Q: 03: A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the…

A: Solution: a) We can find the exit velocity by using energy balance relation as energy during the…

Q: Consider the turbocharger of an internal combustion engine. The exhaust gases enter the turbine at…

A: For turbine: T1 = 450 oC, T2 = 400 oC mass flow rate of exhaust gas = 0.02 kg/s For compressor: T1 =…

Q: Air passes along an insulated horizontal pipe of 0.05 m2 cross sectional area. In the pipe it passes…

A: The density of the air at the inlet can be determined as,

Q: Q4. Fluid enters a condenser at the rate of 40 kg/min with a specific enthalpy of 2000 kJ/kg, leaves…

A: Heat lost by fluid,∆QL=m˙2000-200∆QL=40×2000-200∆QL=72000 kJ/min

Q: Refrigerant-12 enters the condenser of a vapor-compression refrigera- tion system at 175 psia and…

Q: Determine the power required for a forced draught and induced draught fan in a boiler having coal…

Q: Q1/ A gas turbine operates with components as shown in figure 1. Air enters this first compressor at…

Q: electric water heater is fed with an input stream of 15.0 kg/min of water at 17.5°C. Hot water is…

A: 1.

Q: A (293 MW) steam power plant of the pressurized-water Nuclear reactor type uses Once-Through…

A: According to the question, we have Power of the steam power plant, P=293MW change in temperature,…

Q: b) Steam generators are a type of heat exchanges that are used in power plants to generate steam at…

A: Water inlet condition= saturated liquid at 30oCTube diameter, d=60 mm =0.060 mVolume flow rate at…

Q: later vapor with a flow rate of 20000 kg / h enters the condenser of a power plant at a pressure of…

Question

100%

A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 KJ/kg, if cooling water passes through the condenser with temperature increases from 13oC to 24oC. Calculate the cooling water flow rate in kg/sec.

Show conversion of units pls

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 KJ/kg, if cooling water passes through the condenser with temperature increases from 13oC to 24oC. Calculate the cooling water flow rate in kg/sec. pls dont skip anything show all solution including conversion of units
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Pump work in KW. Ans. Ideal heat rate in KJ/KW-hr. Ans. Rankine engine efficiency (%). Ans. Cycle thermal efficiency ( %). Ans
Q1: Steum at a pressure of 28kpa is passed into a condenser and it leawes as condensate at a temperature of sac Cooling water circulates through the condenser at the rate of 45 kg/min - It enters at 152 and Veaves at 3oc If the Steam flow rate is 1.25 eg/min, determinė the drynes fraction of Steam as it enters the condenser.
Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of the condenser is to be saturated liquid at 40°C. Refer to the following figure for stream numbers in your solution. The pressure of the flash chamber and the intermediate pressure between compressors is to be 290 kPa. The evaporator is to operate at -20°C and the outlet is to be saturated vapor. The flowrate of stream 1 is 23 kg/h. The flash chamber may be considered adiabatic. The compressors may be considered to be 80% efficient. a) What is the power input required to the first compressor? b) What are the flowrates of streams 6 and 7? What is the enthalpy of stream 4? Hot Side 6 5 Condenser 2nd Stage Compressor Throttle Valve 7 Flash Chamber Vapor Phase Only 1st Stage Compressor 8 Throttle Valve Evaporator 1 2 Cold Side
Q.2: A refrigeration system using refrigerant 22 is to have a refrigerating capacity of 80 kW. The cycle is a standard vapor-compression cycle in which the evaporating temperature 42°C. -8°C and the condensing temperature (a) Determine the volume flow of refrigerant measured in cubic is meters inlet at the to the compressor. second per (b) Calculate the power required by the compressor. (c) At the entrance to the evaporator what is the fraction of vapor in the mixture.
6- The following reading were taken during a test on a surface condenser: Mean condenser temperature = 35°C Hot well temperature = 30°C Condenser vacuum = 69 cm Hg Barometer reading = 76cmHg Condensation rate = 16 kg/min Cooling water temperature inter = 20 °C Cooling water temperature outlet = 32.5 °C Flow rate being = 37500 kg/h Calculate: a- mass of air present per cubic meter of condenser b- quality of steam at condenser inlet c- vacuum efficiency d- condenser efficiency (condenser heat transfer effeteness)
. 10kg/sec of steam enters a condenser with enthalpy of 2300kJ/kg and velocity of 350m/s , the condensate leaves the condenser with enthalpy of 220kJ/kg and a velocity of 70m/s find the heat transfer to the coolingwater in ton/h.
Steam leaves an industrial boiler at 645.3kPa and 151.2°C. A portion of the steam is fed through a throttling calorimeter and released to the atmosphere when the calorimeter pressure exceeds 104.3kPa. If the calorimeter's steam temperature is 113.8°C, a. What is the amount of moisture that is escaping from the boiler container? Show unit analysis & conversion. b. Calculate the mass of the saturated vapor if the mass of the saturated liquid is 15kg. Show unit analysis & conversion. @645.3kPa and 151.2°C: hf = 624.56kJ/kg hfg =2123.3kJ/kg @104.3kPa and 113.8°C: h2=2506.7kJ/kg
define Mass flow rate of steam
Liquid ammonia at a temperature of 26°C is available at the expansion valve. The temperature of the vaporizing ammonia in the evaporator is 2°C. Find the percentage of liquid vaporized while following throgh the expansion valve. Abs. Pressure kPA Enthalpy kJ/kg hfe 190.4 1255.2 1445.6 303.6 1162.0 Temperature "C 2. 26 462.49 1033.97 1465 6
3.) The steam power plant requires 100 gallons per minute to cool the steam in the condenser from an exhaust pressure of 100 kPa. The feedwater pressure is 100 bar and 500 degrees Celsius. The condensate leaves the condenser at saturated liquid. The cooling tower temperature for the leaving cooling water is 25 degrees Celsius and the cooling water leaving the condenser is 42 degrees Celsius. Calculate the mass of the steam in kg/s assuming ideal rankine cycle and standard density of cooling water.
Determine the heat transfer to cooling water passing through the condenser in KJ/Kg of steam condensed