EP 6.4 Given: air flows into the gas heater at a steady rate, such that at A its absolute pressure 203 kPa, its temp is 20°C and its velo is 15 m/s. when it exits at B, it is an absolute pressure of 150 kPa and a temp of 75°C. 100 mm 15 m/s AT 150 mm 3- Vo B Find: Determine its velo at B.

EP 6.4 Given: air flows into the gas heater at a steady rate, such that at A its absolute pressure 203 kPa, its temp is 20°C and its velo is 15 m/s. when it exits at B, it is an absolute pressure of 150 kPa and a temp of 75°C. 100 mm 15 m/s AT 150 mm 3- Vo B Find: Determine its velo at B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2-14. At the bottom of a bottle a bubble within carbonated water has a diameter of 0.2 mm. Determine the bubble's diameter when it reaches the surface. The temperature of the water and bubbles is 10°C, and the atmospheric pressure is 101 kPa. Assume that the density of the water is the same as that of pure water. 2 300 mm Prob. 2-14
Heavy fuel oil flows at Q = 10 gallons per minute (gpm) in a horizontal steel pipe that connects two storage tanks. The diameter of the pipe is D = 1.5 inches. The length of the pipe is L = 100 feet. The depth of oil in the supply tank is 30 feet above the pipe entrance. The temperature of the oil is 60°F, the specific gravity of the oil is s.g.oin = 0.90, the specific weight of the oil is 56.13 lb/ft', and the kinematic viscosity of the oil is 0.00175 ft2/s. The pipe discharges into the bottom of the receiving tank. Neglect minor losses. a) Determine the pressure p at the pipe entrance in pounds per square foot (psf). b) Determine the velocity v in feet per second (fps). c) Determine the Reynolds number Re. d) Classify the flow based on the Reynolds number Re. e) Determine the Darcy-Weisbach friction factor f. f) Determine the friction head loss hfac in feet in the pipe between the two storage tanks. 8) Determine the depth of oil in feet above the exit from the pipe into the second…
Q2// Consider a special ball made of steel (p- 5000 kg/m', Cp- 300 J/kg. k, A= 60 m²). The initial temperature of the ball is 300 K. It is immersed in a large oil tank at 400 K. The convective heat transfer coefficient, h at the sphere surface is 3000 W/m³. k. Assume that there is no radial temperature gradient inside the ball. Use Euler's method to find the temperature of the sphere at t = 15 sec after it was immersed in the oil tank. Use a step size of h= 5 sec. The energy balance equation of the ball is given by the following equation: dT pCp -=-hA(T-T₂) dt
66 Fluid Mechanics (Ans. (a) 0.3924 N/cm², (b) 0.353 N/cm², (c) 5.33 N/em²} kg 13.6. Take density of water, p= 1000. (Ans. (a) 5 m of water, (b) 6.25 m of oill is : (a) water, and (b) an oil of sp. gr. 0.8. (Ans. 16 m) height of water at that point. 6. An open tank contains water upto a depth of 1.5 m and above it an oil of sp. gr. 0.8 for a depth of 2 m. Find the pressure intensity : (i) at the interfäce of the two liquids, and (ii) at the bottom of the tank. [Ans. (f) 1.57 N/cm², (if) 3.04 N/em"] 7. The diameters of a small piston and a large piston of a hydraulic jack are 2 cm and 10 cm respectively. A force of 60 N is applied on the small piston. Find the load lifted by the large piston, when : (a) the pistons ar at the same level, and (b) small piston is 20 cm above the large piston. The density of the liquid in the jackis [Ans. (a) 1500 N, (b) 1520.5 NJ kg given as 1000 m 8. Determine the gauge and absolute pressure at a point which is 2.0 m below the free surface of water. Take…
The distance Ah is the height of the liquid in the manomoter above the heavier liquid in the tank. D 10 cm Water Ah = ? B C 20 cm S= 3.0
Oil of sp.gr. of 0.750 flows through the nozzle shown and deflects the mercury in the U-tube gage. Determine the value of H in m if the pressure at A is 142 kPa.
Q,; A liquid of (u = ) shown in figure below. Calculate the forque (T) required = 1- 25 Pa.s.) fills the space of (Smm) to rotate the frustum cone at a constant speed of (60 rip.u). o. 3m c.7m
1. When the force of 3 mN is applied to the plate the line AB in the liquid remains straight and has a velocity of 0.6x103 m/s. If the surface area of the plate in contact with the liquid is 0.6 m2, determine the approximate viscosity of the liquid. В в B B' 3 mN 4 mm A
Q2: A drop of liguid foluen is kept al uniform temperkure t 299 K and is suspended in air by a fine wire. The initid radius at r= 2mm. The vapor pressure of foluene 299K is f=384 Kfe and the density of liguid toluene is 366 ky Im 3. Derive equation for the time tp for the drop b evupurete Completely in a large volume of still air Calculate the tine in seconds for Complete evaporahion.
4. The pressure intensity at a point in a fluid is given 4.9 N/cm². Find the corresponding height of fluid when it 5. An oil of sp. gr. 0.8 is contained in a vessel. At a point the height of oil is 20 m. Find the corresponding m [Ans. (a) 5 m of water, (b) 6.25 m of cil is : (a) water, and (b) an oil of sp. gr. 0.8. (Ans. 16 m) and pbove it an oil of sp. gr. 0.8 for a depth of 2 m height of water at that point.
*2-40. Butyl carbitol, used in the production of plastics, is stored in a tank having the U-tube manometer. If the U-tube is filled with mercury to level E, determine the pressure in the tank at point B. Take Sug = 13.55, and S = 0.957. A 300 mm E 50 mm 120 mm CDE 250 mm 100 mm B Mercury Probs. 2-39/40
The same open tank now contains three immersible liquids as shown. Because of the system geometry, piezometer A contains liquid A, piezometer B contains liquid B, and piezometer C contains liquid C. Determine (a) the gage pressure at the interface between liquids A and B, at the interface between liquids B and C, and at the tank bottom; (b) the elevation of the liquid surface in piezometer A; (c) the elevation of the liquid surface in piezometer B; (d) the elevation of the liquid in piezometer C. (e) redraw the sketch and show the liquid to the correct elevation in each tube.