Check the adequacy of column AB for applied live load. Fy= 350MpaW360x51:A= 6450mm2rx= 148mmry= 38.8mmd= 355mmb=171mm== 11.6mm-=7.2mmAB2mW36-X51M3"GookN/m (Live load)D3m

fy = 350 MPaCompression member:W 360 x 51A = 6450 mm2 rx = 148 mmry = 38.8 mmd = 355 mmb = 171 mmt =…

Answered: Check the adequacy of column AB for…

Engineering

Civil Engineering

Check the adequacy of column AB for applied live load. Fy= 350M

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: No

Q: In each item, solve the support reactions. Draw the shear and moment diagram. Label them properly.…

A: Note : Since you have asked multiple questions, we will solve the first question for you. If you…

Q: B1- Use the moment-area method to determine the slopes and deflections at points B and C of the…

A: A simply supported beam is loaded as follows

Q: A W30 x 99 beam carries a concentrated live load of 890 kN at its mid-span. Neglect its own weight.…

A: Pn = Fy tw (d - 2k)where:Pn is the design strength for beam web yieldingFy is the yield strength…

Q: Please solve this problem using method of sections and please show all of your work in pictures…

A: Given Load 6 and 6 kNSpan 9 mTo find out Member forces

Q: The following beam in a building is subjected to equipment loading (M and P), they are documented as…

Q: The soil of an 21 degree infinite slope is subjected to full depth seepage. The soil properties are…

Q: Use Force Method. Determine the reactions at the supports, then draw the moment diagram for each…

A: Given:Required:Support reaction and moment diagram

Q: uss. Each m A 300 mm². E= work. =

Q: A flow of 0.03 m³/s must be pumped against a head of 30 m. The pump will be driven by an electric…

A: Q=0.03m3/sechead(H)=30mspeed(N)=2000rpm

Q: Calculate specific yield of an aquifer if a = 9.9 and B Discharge = 80 L/s Max drawdown = 0.8 m…

Q: For the beam below, show that a. Max. Shear: 20 kN b. Max. Bending Moment: -20 kN-m c. Location in…

A: A simply supported overhang beam is shown in the above figure. We have to show the followings:…

Q: Can you give the answers in KN please please it's urgent

Q: Please help me answer the given question for the case study 1. A manufacturing enterprise pays…

A: Bob, a key management figure, finds himself at the crossroads of ethical and practical…

Q: Determine the force in members AE, BE and BC of the given truss. State whether each member is in…

Q: For the beam shown, find the resultant force and determine the necessary reactions to ensure static…

A: A simply supported beam is loaded with a parabolic load as shown,To determineThe resultant loadThe…

Q: Air discharges from a 2-in.-diameter nozzle and strikes a curved vane, which is in a vertical plane…

A: D = 2 in = 22.5o = 7 in or 0.583 ft

Q: 1. For the beam and loading shown and knowing that the distributed load w can be expressed as a…

A: A cantilever beam is loaded with a parabolic loading, w = kx2, and the span of the beam is 18ft,…

Q: Problem 1: Determine the slope and the displacement at C. El is constant. Use consistent units, i.e.…

A: E = 29000 ksi I = 1000 in.4 Determine the slope and displacement at C using Conjugate beam method.

Q: Determine the Moment of Inertia about the X' axis if angle between X' and Xo is 30.1 degrees

A: Given:Angle between xo and x' is 30.1°Required:Moment of inertia about the x' axis

Q: A trapezoidal channel has a bottom width of B=5 m, sidewall slope of 1V:1H, and bed slope of…

A: Botom width of channel, Bed slope, Side slope, Mean diameter, Manning coefficient for side walls,…

Q: The city public transportation. authority manages and maintains the regular bus service. If the…

A: two travelling modes as follows

Q: A telescope with tripod weighs 40 pounds and has geometry as shown in the figure and parameter…

Q: Water is pumped up from a reservoir to a smaller holding tank. If the flow rate through the pipe is…

A: NPSH is the net positive suction head, which is measured in the centrifugal pump.If the local…

Q: ease discuss the effect of Pollution on Lake

A: Water pollution occurs when harmful and undesirable substances are introduced into it, causing a…

Q: Draw moment diagrams for the frame below. The columns are 15 ft high, and the beam is 25 ft wide…

Q: EXI m DETERMINE р de 10KN 10KN 9 B 10624m E # 3

Q: At the instant shown in (Figure 1), the car at A is traveling at 10 m/s around the curve while…

Q: 2. The pipe connection shown is a series-parallel connection. The rate of flow in pipeline 1 is 300…

A: Friction factor (f) = 0.02Discharges in pipe lines 2, 3 and 4 =?

Q: 18. Air with a density of p = 1.2 kg/m³ flows in an inclined ventilation duct having a cross-…

Q: The reaction at the support D of the continuous beam ABCD, hinged at two points shown in below…

Q: Determine the deflection at joint B. Members have the same moment of inertia of 1440 x 10^4 cm^4 and…

A: Given:Required:Deflection at joint B

Q: a) A 406x178x54-1 steel section is strengthened by welding a 177.6mm x 6mm plate to one flange as…

A: Note: “Since you have posted multiple questions, we will provide the solution only to the first…

Q: Determine the Allowable number of repetitions for a base quality material with 3.8% cement material.…

Q: Problem 1 Determine the minimum height h of the beam shown in the Fig. if the flexural stress is not…

A: Allowable flexural stress = 23 MPa = 23 N/mm2 Minimum height of the beam =?

Q: 1- The # blows increases as the water content increases in liquit limit test 2- Shrinkage limit is…

A: Soil testing plays a crucial role in assessing soil properties and behavior, and is a fundamental…

Q: Problem 8: A firm producing poultry feed finds that a new production method needs to purchase an…

A: The breakeven quantity represents the volume of units a company must sell to cover all its expenses…

Q: If the viscosity of ground water is 1.00, the Slitcher's constant is 400, the effective size of soil…

Q: rnal pin) pent 3' p lok.ft B5 с F I al Sek F 2k/ft 44²+4²-9 8 ft 6ft, 6ft +4 + E # It K 3.3 ttt off…

A: Given data, fig is givenFINDreactions at the supports

Q: Calculate the count of cycles resulting in breakdown. Given Crack length = 0.2 mm 3 Fracture…

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

Q: Where it get the value 2 and 10 for the green circle? Please expl

A: This question is related to the Design concrete structures.In this question ask about the , Where it…

Q: 3. Determine the reactions at the supports -3m- 400 N/m -3 m-

Q: A fluid is placed between two parallel plates with area of 2 m². The lower plate is pulled with 0.4…

A: v1=0.4m/secF1=0.4Nv2=?F2=0.75N

Q: Determine the deflection at the left overhanging end Using Conjugate Beam Method A Assume constant…

A: Given:Required:Deflection at the left overhanging end

Q: -Q2.23-. A cantilever beam shown is reinforced with 7- 25 mmø at the top and 4- 16 mmø at the…

A: Development length is the minimum length of the steel bar embedded in concrete due to the full…

Q: Some waste has a five-day BOD (biochemical oxygen demand) at 20 oC , equal to 210 mg/L and an…

A: Given data, five-day BOD (biochemical oxygen demand) at 20 oC , equal to 210 mg/L ultimate BOD…

Q: Referring to the figure below, solve for A. 6" 8" -40"- FL E EQUAL SPREAD 45° OFFSET -15"→ B 14" D

Q: 3. The compound beam given in the figure is composed of a pair of beams, AB and BC, connected by a…

Q: The water jet is ejected from the 4-in.-diameter pipe with a steady velocity of v = 20 ft/s. It…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

Check the adequacy of column AB for applied live load. Fy= 350Mpa
W360x51:
A= 6450mm2
rx= 148mm
ry= 38.8mm
d= 355mm
b=171mm
== 11.6mm
-=7.2mm
A
B
2m
W36-X51
M
3"
GookN/m (Live load)
D
3m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given:

VIEW

Step 2: Solution:

VIEW

Step 3: Calculate the buckling strength for governing slenderness ratio:

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q3// Find spacing required for stirrups 08mm at zone A and zone B for the beam shown with the factored loads, use, fé = 25MPA, fy = 300MPA. %3D %3D Pu = 42kN Pu = 14kN 65mm Wu = 40kN/m 435mm 1.2 m 1 m 250mm- Vu = 144kN 96KN 54KN Zone A 14kN Zone B
Typing f Facebc (1) Me M Fwd: F E Sta X E Statics G detern G teremi S HW11 nt/d/1DJXbp051_Aq9VmLFLk-ukINmQzs-MT107ZoOyL3D4Ng/edit 100% Normal text Calibri 11 BI 3 4. 6 kipe 10 ft B. Determine the forces in members FH, DH,EG and BE in the truss using the 3kips 10 ft D. kups t ft method of sections. 1 ft 15 it
B 4 60 kips 20- EX/ Analysis all member G 20' P4.18 F 60 kips 20 15' 30 kips 15'
4.5.12 OIC Section Properties Write functions for A, I, c, radius of gyration. Each function works for the three sections below. Example Function name: OICSEC_A() • OICSec_() Etc. 을 + 12 BIP - bhs V, 12(BII-bh) BII -- bha 6/1 - 8
d?y dy 7y = 6e2x, dx2
PROBLEM 01 REFER TO FIGURE 01, DETERMINE THE INTERNAL FORCES ACTING ON THE FOLLOWING MEMBERS: (STATE COMPRESSION OR TENSION) o FG o FC GH CH
plss h8lp.
There is a statically indeterminate beam in which the horizontal force at the left and right ends (points A and D) is zero, and the vertical force is shown in the figure below, The flexural stiffness of the beam section is constant El: Try to find the slope (Slope) of point B after deformation.
Problem No.1 Calculate the allowable uniform load W that the beam could carry. Assume fc' = 28Mpa, Ey 415Mpa, diameter of stirrups 10mm. %3D %3D a. Depth of N A. mm b. fs' Mpa c. Mcap kN-m d. W Nm 275mm 2-16mm Dia .. W KN/M 5.50m 6-16mm Dia 60mm Edit View Insert Format Tools Table 12pt - Paragraph BIUA Da 9f
H.W: draw the I.L for RA, RC, RF, RD, MD, VCL, VG and MG. A 2 m B -2 m C G 0.4 m 1.6 m D 2 m- E 2 m LL
Q5) 1- Max shearing stress? 2- The necessary distance between pins and number of these pins of diameter 10mm can be used in longitudinal direction of beam? Knowing that the allowable shear stress of bolt is 25 MPa. 20mm 120mm re) For the beam shown in Figure (4), compute: 180mm H H 20mm 20mm 5 kN 1m m Figure (4) 2m 10 kN/m +4 2m 1m 5 KN
This problem is about replacing the loading system acting on the beam shown below by a resultant force and a couple moment at acting at Point O. Oppfz 350 lb-ft 50pff ∙100th £40016 Determine: a) The resultant couple moment (MRO). Provide the direction of rotation (CW or CCW). b) The component of the resultant force in the x-direction (FRx). Provide the direction of the force. c) The component of the resultant force in the y-direction (FRY). Provide the direction of the force.