(e) Consider the circuit of Figure 1.5 consisting of a MOSFET M¡ biased in saturation. Which of the following values corresponds to resistance R1 required to bias the DC output voltage V, to 5V if the MOSFET is characterised by a threshold voltage of 1 V and a K= 2mA/V². %3D R3 2kN R1 Vo = 5V Vs 10V M1 Vin R2 35kN Figure 1.5 (A) R¡ = 18.6 kN (B) RỊ = 13.85 k2 (C) R1 = 12.42 kQ (D) R1= 14.37 kN

(e) Consider the circuit of Figure 1.5 consisting of a MOSFET M¡ biased in saturation. Which of the following values corresponds to resistance R1 required to bias the DC output voltage V, to 5V if the MOSFET is characterised by a threshold voltage of 1 V and a K= 2mA/V². %3D R3 2kN R1 Vo = 5V Vs 10V M1 Vin R2 35kN Figure 1.5 (A) R¡ = 18.6 kN (B) RỊ = 13.85 k2 (C) R1 = 12.42 kQ (D) R1= 14.37 kN

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit given in figure below draw the collector characteristic curves for IB = 50,150 and 250 micro amperes on the same graph
QUESTION 4 In this voltage divider bias circuit, the input is at the base. Output is at the emitter with a high input resistance and low output resistance. The maximum voltage gain is 1 and the coupling capacitors must have a negligible reactance at the frequency of operation. (use to answer a and b) a. Derive the expression for the voltage gain, current gain, and power gain in terms of power delivered to the load, RL. b. Sketch both the DC and AC equivalent circuits. c. Derive the expression for ripple factor of Half Wave Rectification with a capacitor filter.
Problem #6: An abrupt p-n junction varactor is used to tune an oscillator shown in Figure 3. At zero bias voltage, the varactor has a junction capacitance of 4pF, Vbi 1.3V for GaAs. The active device has CD = 2pF and RD = 10W. The load bias has L₁ = 15nH and R₁ = 10W. What are the oscillation frequencies at (a) -20V (b) -10V and (c) OV? = L₁ R₁ C₁ (V) -RD FIGURE-3 www CD
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration
Determine vo versus v₁ for the circuit shown in Figure 2. Assume that the MOSFET operates in saturation and is characterized by the parameters K and VT. Vs R₁ www Figure 2 wwww RL R₂ wwwww VO Note: assuming the MOSFET works at normal saturation regime and ips= (VDS -VT)²2 K 2
In this voltage divider bias circuit, the input is at the base. Output is at the emitter with a high input resistance and low output resistance. The maximum voltage gain is 1 and the coupling capacitors must have a negligible reactance at the frequency of operation. (use to answer a and b) a. Derive the expression for the voltage gain, current gain, and power gain in terms of power delivered to the load, R. b. Sketch both the DC and AC equivalent circuits. c. Derive the expression for ripple factor of Half Wave Rectification with a capacitor filter.
circuit shown in the figure, Kn = 2mA / V2, VIN = 0.7V for Mi mosfeti. So, what kind of relationship should there be between R1 and R2 resistance for mosfet to work at saturation?
Q-3. Find the drain-source voltage, Vos, for the E- MOSFET circuit given below. The device parameters are: Ioss = 4 mA and Vm = 2 V. +15V Rp- 2k 4M R1 + Vps 2M R2
A 4.7 zener diode is connected to the base resistor. The left side of the resistor sits at about 12V. The right side of the biasing resistor is connected to the Zener and npn transistor. The Zener bias is 5mA. The base current needed is 80uA. What is the appropriate resistor for this circuit? (In kohms) I
Question No. 2 a Inan experiment the voltage required for the device is 9V dc but unfortunately the transformer avai lable is of 220-6 V dc. Design a circuit which can power the device (use only methods that we have studied excluding Zener diode) b. Explain the behavior of the foll owing circuits if the input signal is triangular wave of peak voltage 5V and the biasing battery of 3V 4-
Questiona. In an experiment the voltage required for the device is 9V dc but unfortunately the transformer available is of 220-6 Vdc. Design a circuit which can power the device (use only methods that we have studied excluding Zener diode)b. Explain the behavior of the following circuits if the input signal is triangular wave of peak voltage 5V and the biasing battery of 3V
please give detail explain.. Ans : Rth = 28 ohm Vth = 92 V