Dron Acompound steel [G=80 GPa) shaft consists of a solid 110-mm-diameter segment (1) and a solid 56-mm-diameter segment (2). The allowable shear stress of the steel is 96 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to 54°. Determine the magnitude of the largest torque that may be applied at C. (1) 120 (2) 18 Te

Dron Acompound steel [G=80 GPa) shaft consists of a solid 110-mm-diameter segment (1) and a solid 56-mm-diameter segment (2). The allowable shear stress of the steel is 96 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to 54°. Determine the magnitude of the largest torque that may be applied at C. (1) 120 (2) 18 Te

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

0.15
The steel bar AB has a diameter of 30mm and is connected to the brass bar BC. The two bars are fixed to unyielding supports at the top (point A) and bottom (point C) ends. If there is a temperature rise of 50°C, calculate the compressive force induced in the rods (ABC). Note: For steel (E = 200 GPa, as = 11.7 x 106 °C) and for brass (E = 105 GPa, qb= 20.9 x 10-6/ °C). 250 mm 300 mm A B -30-mm diameter -50-mm diameter
Compound axial member ABC has a uniform diameter of d = 1.25 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 = 100 in. • Segment (2) is a copper [E2 = 17000 ksi] alloy. The length of segment (2) is L2 = 140 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2 = 2300 uin./in. in the longitudinal direction. What is the total elongation of member ABC? L2 (1) Aluminum B (2) Copper Answer: in, AL = i
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 540 mm?. If the stress in the bar must not exceed 450 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b = 2.4 m, and c = 5.2 m. (1) B' A a Answer: P = i kN
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T
i need the answer quickly
Two steel rods are welded together (see figure);the seam is oriented at angle θ = 50°. The stresses onthe rotated element are σ x1 = 10 ksi, σy1 = -12 ksi,and τx1y1 = -5 ksi. Find the state of plane stress onthe element if it is rotated clockwise to align the x1axis with the longitudinal axis of the rods.
I will rate immediately
A stress developed if the applied force is parallel to the resisting area refers to: O tangential O bearing O normal. O simple
The general stress element shown is loaded such that o = 20 MPa, oy = -20 MPa, Txy = 10 MPa. What is the max dy 1 xy 70x
17