22) One brass bar and one steel bar are forming the setup shown below. Determine the tresses and the strains in the steel and brass bars when a load of 750 kN is applied to he connection of these two members where modulus of elasticities for steel and brass are Est = 200 GPa and Ebr = 125 GPa, respectively, and cross-sectional areas for steel and rass bars are Ast = 700 mm² and Abr = 1000 mm², respectively. Fixed Support 500 mm 400 mm Brass Steel F mm Gap F-750 kN Fixed Support

22) One brass bar and one steel bar are forming the setup shown below. Determine the tresses and the strains in the steel and brass bars when a load of 750 kN is applied to he connection of these two members where modulus of elasticities for steel and brass are Est = 200 GPa and Ebr = 125 GPa, respectively, and cross-sectional areas for steel and rass bars are Ast = 700 mm² and Abr = 1000 mm², respectively. Fixed Support 500 mm 400 mm Brass Steel F mm Gap F-750 kN Fixed Support

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A high-strength steel band saw, 24 mm wide, runs over pulleys 900 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 310? Assume E= 230 GPa. Answer must be in mm.
Two aluminum plates, each having a width b = 7.5” and thickness t = 2”, are welded together as shown in the figure. Assume that a = 5.0”. Specifications require that the normal and shear stress magnitudes acting in the weld material may not exceed 40 ksi and 25 ksi, respectively.
Ch 1. Answer with complete solution. Thankyou.
Compute the maximum force F (in KN) that can be applied to the composite rod if the allowable total deformation of the composite rod is limited to 0.80 mm A 6F B Steel Rod d = 100 mm L = 3 m E = 200 GPa C Aluminum Rod d = 70 mm L = 2m E = 70 GPa 3F D Bronze Rod d = 40 mm L = 4 m E = 80 GPa 2F
I want the solution of these question
Two steel plates each of width 150mm and thickness 10mm are connected with three 20mm diameter rivets placed in a zig-zag pattern. The pitch of the rivets is 75 mm and gauge is 60mm. If the allowable tensile stress is 150 MPa, the maximum tensile force that the joint can withstand is
please answer question below step by step fill in all blanks, charts, stresses, and tresca
Asiacell|Asiacel K/s Asiacell For simply supported beam with rectangular cross section shown, determine the values and location of the maximum tensile and compressive bending * stresses 1000 lb 400 lb/ft 6 in DV 8 in 10 ft RA Rp
A steel cantilever beam is fabricated from two structural tees welded together, as shown in the figure. For this beam, the allowable bending stress is 150 MPa, the allowable shear stress of the steel is 100 MPa, and the allowable shear flow along the weld is 2MN/m. Determine the allowable force P that the beam can carry. (All dimensions are in mm).
Please no hand writing solution
N = 7
Compute the maximum force F (in KN) that can be applied to the composite rod if the allowable total deformation of the composite rod is limited to 0.80 mm A 6F B Steel Rod d = 100 mm L=3m E = 200 GPa C Aluminum Rod d = 70 mm L = 2m E = 70 GPa 3F D Bronze Rod d = 40 mm L = 4 m E = 80 GPa 2F