Determine the force P necessary to close the gap at the steel post. The steel post is 2 inch x2 inch square and 8 in high. The aluminum alloy bar is 1.5 inch wide by 1 inch thick and 20 in long. The horizontal bar is considered rigid as are the loading caps at the steel post. The modulus of elasticity for the steel is 30,000 ksi, that of aluminum is 10,000 ksi. The yield stress for the steel is 36 ksi, that of the aluminum is 40 ksi. Aluminum

Determine the force P necessary to close the gap at the steel post. The steel post is 2 inch x2 inch square and 8 in high. The aluminum alloy bar is 1.5 inch wide by 1 inch thick and 20 in long. The horizontal bar is considered rigid as are the loading caps at the steel post. The modulus of elasticity for the steel is 30,000 ksi, that of aluminum is 10,000 ksi. The yield stress for the steel is 36 ksi, that of the aluminum is 40 ksi. Aluminum

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (ay) MPa, and for the bronze (ay)or 520 MPa, determine the magnitude of the largest elastic load P 640 that can be applied to the assembly. E 200 GPa, Ebr= 100 GPa. 10 mm 20 mm Figure 2: Steel Bolt
Problem 1 An axial force of P is applied to the center of the rigid end plate shown below. If the portion of the load carried by the aluminum plates is half the portion of the load carried by the brass core, (a) determine the value of h, (b) the total load if the stress in the brass is 50 MPa. Brass core (E = 105 GPa) Aluminum plates (E = 70 GPa) Rigid end plate 300 mm 60 mim 40 mm
The member consists of the steel rod AB that is screwed into the end of the bronze rod BC. Find the largest value of P that meets the following design criteria: (i) the overall length of the member is not to change by more than 3 mm; and (ii) the stresses are not to exceed 140 MPa in steel and 120 MPa in bronze. The moduli of elasticity are 200 GPa for steel and 80 GPa for bronze. A Steel 1.0 m A = 480 mm² В 3P Bronze A = 650 mm² 2 m 2P
The 200-mm square aluminum block supports a compressive load of 300 kN. What is the normal stress acting on section a–a in MPa What is the shearing stress acting on section a–a in MPa The lapbelt assembly is to be subjected to a force of 800 N. What is the required thickness t in mm. of the belt if the allowable tensile stress for the material is 10 MPa?
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
The modulus of elasticity of mild steel is equal to .. .? .... .. a. 2 x 10ʻN/m? a. 2 x 10'N/m 2 b. 2 x 10° N/m 4 c. 2 x 10 N/mm 5 d. 2 x 10 N/mm Check
NEED IN 1 HOUR PLS, THANK U A copper bar is of uniform cross-section and is rigidly attached to the walls as shown. The rod is 5ft long and has a cross-sectional area of 2.5 in². At a temperature of 20°F the rod is stress-free in the configuration shown. Determine the stress in the rod when the temperature has dropped to 50°F. Assume that the supports do not yield. For copper, E = 16x10⁶ lb/in² and α = 9.3 x 10^-6/°F.
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
The light rigid bar ABCD shown Is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. E200 CPa E1m 2.0 m 0.6m 1.5 m VP-20 KN Aluminum E-70 GPa A=900mm2 L-1.5 m What is the axial stress at steel rod in MPa?
A compressive load P is transmitted througha rigid plate to three magnesium-alloy bars that areidentical except that initially the middle bar is slightlyshorter than the other bars (see figure). The dimensionsand properties of the assembly are as follows:length L = 1.0 m, cross-sectional area of each barA = 3000mm2, modulus of elasticity E = 45 GPa,and the gap s = 1.0 mm.(a) Calculate the load P1 required to close the gap.(b) Calculate the downward displacement d of therigid plate when P = 400 kN.(c) Calculate the total strain energy U of the threebars when P = 400 kN.(d) Explain why the strain energy U is not equal toPδ / 2. Hint: Draw a load-displacement diagram.
The following steel member is connected to the gusset plate via two longitudinal welds. The width of the member is 58 mm and the length of the weld is 87 mm. The yield stress is 300 MPa and the ultimate stress is 675 MPa. The gross area of the member is 700 mm^2 . a. What is the tensile design yield strength in KN? b. What is the tensile design rupture strength in KN? c. If a tensile load of 85 KN is requiredfor the member, what is the minimum factor of safety for the steel member?
8 ksi, oy The normal stresses at a point in a steel member are ox 10 ksi. Using E -4 ksi, 29 x 103 ksi and v = 0.3, determine the normal strains at 2.31 %3D and oz this point. %3D ר- The rectongulor block, of material of€ length Land cross sectional ore 1 fits