drawing. The bar is threaded through the holes, loaded with fully variable load from the pins. Find the maximum load F to be applied to the part so that the part can have an indefinite life by looking at the appropriate figures for the stress concentrations that

Q: A straight bar of circular cross-section has a diameter of 50 mm. The bar is subjected to a time…

A:

Q: A M12 x 1.25 hex-head bolt with a nut is used to clamp two 25-mm thick steel plates. The nut height…

A: Given:- Elastic modulus 207 GPa Bolt size= M12 x 1.25 Height of nut =10.8 To find:- d) Bolt…

Q: Prob. 2.3-16. A steel restraining ring in the form of a toroid with rectangular cross section is to…

A:

Q: A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric…

A: Given: Su = 345 MPa Load, P = 13 kN

Q: The plate of the figure is subjected to a bending moment with irregular cycles, which are repeated.…

A: NOTCH SENSITIVITY FACTOR(q) It is defined as the susceptibility of a material to succumb to the…

Q: a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a…

A: Given       Tensile load, P =3 kN        Cross-section = 4mm X 4mm Find The applied engineering…

Q: The cantilever bar in the figure is made from a ductile material and is statically loaded with Fy=…

A: The forces acting on the cantilever beam are: Fy = 300 lb Fx =0 Fz =0   To find: The critical…

Q: 450-mm-long AISI 1020 steel rod is subjected to a tensile load of 55 kN. The allowable tensile…

A: Given Length = 450 mm Tensile load = 55 kN = 55 X 103 N Allowable tensile stress = 140 MPa = 140…

Q: A M12 x 1.25 hex-head bolt with a nut is used to clamp two 25-mm thick steel plates. The nut height…

A: Note:- As per our company guidelines we are supposed to answer only the first three sub-parts.…

Q: A copper rod of 50mm diameter is surrounded by a steel tube of 100mm external diameter, the ends…

A:

Q: A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R1and R2. The…

A:

Q: A cylindrical specimen of a steel alloy having a diameter of 12.8 mm and a gauge length of 50.8 mm…

A: Given dataFOS=2.5F=8230 NTo find the shank diameterof SQeW

Q: Q1. For the system shown in Figure 1A. The fillet of 6 mm radius for this member is critical. Cons D…

A:

Q: A cylindrical boiler with an inside diameter of 2.5 m and a wall thickness of 40 mm is made of a…

A: GIVEN DATA- Pressure P=1.5MPa Internal Dia d=2.5m = 2.5*1000=2500mm Thickness t=40mm Yield stress…

Q: A bracket is designed with a pin-pin horizontal tie rod supporting a boom that is also pinned at two…

A: Given data as per question vertical load =6 KN Tensile yield strength =400 Mpa Considering FBD of…

Q: Figure: Circular prismatic rods with negative torques at each end. The circular rod shown has an…

A:

Q: You are in charge of designing a new fixture for a “universal testing machine” that will attach a…

A: The data given is, Maximum load = 30 kN Maximum permissible shear stress, σ = 600 Mpa To…

Q: 3. A cylindrical metal rod of 50mm diameter and 3m length is subjected to a tensile load of 150KN.…

A: Strain is the deformation in the material per unit length. True strain is the natural log of the…

Q: A bar of circular cross-section is subjected to alternating tensile forces varying Example 4 from a…

A:

Q: A M12 x 1.25 hex-head bolt with a nut is used to clamp two 25-mm thick steel plates. The nut height|…

A: Give:- At=84.3 mm2 F=12 kN To find:- g) Stress in bolt

Q: A bar is subjected to fluctuating tensile load from 20 kN to 100 kN. The material has yield strength…

A: Given:P1=20 kNP2=100 kNσy=240 MPaσe=160 MPaFactor of safety=2

Q: Part (a) of the figure below shows a knuckle joint with a pin inside it. This joint is subject to a…

A: Given-Fluctuating load F-on and 600NAISI Hot- rolled stealFatigue stress concentraion factor-

Q: Problem 1: For a 20-ply lay-up [(0/90)s]s in which ply thickness is 0.1 mm and stiffness is: 20. 0.7…

A: Solution:   Given Data:

Q: Rods (1) and (2) were supposed to fit exactly between the rigid walls at A and C, as indicated in…

A: Given DataE1=74 GPaA=1749 mm2L=738 mmE2=204 GPa

Q: For the screw clamp shown, a force is applied at the end of the handle 3 in from the screw…

A: Given Data:- L=3.5 in T= 3.5 F

Q: Find the equivalent stresses at Points 1 and 2 of the element with given geometry and loading…

A: Given, Shaft diameter, d=20 mm=0.020 m Shaft length, L=120 mm=0.12 m F1=750 N F2=3000 N Torsion,…

Q: Taking the safety factor as 2 for the loading condition shown in the figure, we can calculate the…

A: Given: d=100mm Syt = 250 MN / m2 Sys = 140 MN / m2  E = 200 GPa μ=0.3 N = 2

Q: A tensile stress is to be applied along the axis of a cylindrical brass rod with diameter of 200 mm.…

A: since you haven't mentioned the value of poison ration and elastic modulus that's why the reference…

Q: In the system given in the figure, the rods are identical and it is desired to be produced in the…

A:

Q: The factors that creep rate depends on? Write 4 of them. Plot the creep-load curve and show its…

A:

Q: Q4: Design a scissor jack Power Screw for Fig. (A) and Fig. (B) made of (1035 hot rolled Carbon…

A:

Q: The cantilever bar in the figure is made from a ductile material and is statically loaded with Fy=…

A:

Q: Q-8 A tensile test specimen of stainless steel alloy having a diameter of 12.6 mm and a gage length…

A: Part (a) Modulus of elasticity: It is defined as the ratio of longitudinal stress and strain. In a…

Q: Example:- A three 1in *3in wood board is connected together by bolt (d-0.5in) as shown in the…

A:

Q: A tension bar 100mm x 10mm is to carry a load of 150kN. A specimen of the same quality steel of…

A:

Q: steel bar is desired to be formed until it has a final length of 1.8m. What length sould the bar in…

A:

Q: In the state of loading as made of brittle material tensile and compression fracture values ​​of the…

A: Given data In the state of loading as made of brittle material tensile and compression fracture…

Q: A copper rod of 50mm diameter is surrounded by a steel tube of 100mm external diameter, the ends…

A: Given data  diameter of copper rod (d) = 50 mm  outer diameter of steel tube (D) = 100 mm…

Q: Determine the safe tensile load for bolts of M20 and M42 . Assume that the bolts are not initially…

A: We know that ,  when a bolt is subjected to tensile load , Pt=σt×As=σt×πd24 where , Pt=tensile load…

Q: Hooke's Law Part B - Calculate the elongation under load A bar with a solid square cross-section is…

A: Find the total elongation of bar and permanent change in length of bar.

Q: n Figure 1, with its dimensions, loading status and material properties, different full circle…

A: Given data

Q: The cantilever bar in the figure is made from a ductile material and is statically loaded with Fy=…

A:

Q: 2. The figure shows welded hand rotates a shaft via a key. The key material allowable shear strength…

A: Given data: 1. Force acting on the weld 2. Dimensions of the weld and other dimensions. Both  the…

Q: 1. A cold drawn mild steel, AISI 1018CD is used to fabricate the hollow shaft as shown in Figure Q1.…

A:

Q: A cylinder head for steam engine is held by (14) bolts. The effective diameter of the cylinder is…

A:

Q: 1. A copper bar of 12 mm diameter gets stretched by 1 mm under a steady load of 4 kN. What stress…

A: Given Data Diameter of the bar is: d=12 mm The change in length of bar is: dl=1 mm Load on the bar…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.