A copper rod of 50mm diameter is surrounded by a steel tube of 100mm external diameter, the ends being firmly fastened together, subjected to a compressive load of 30kN. Youngs modulus of elasticity of steel is 200GPa and that of copper is 120GPa. Evaluate the stress produced in the copper rod and steel tube.

Q: A reinforced concrete collumn 200mm in diameter is designed to carry an axial compressive load of…

A: Answer: The required cross-sectional area of the reinforcing steel is 1650 mm2.

Q: The rectangular bar shown is connected to a support bracket with a 27 mm diameter pin. The width of…

A:

Q: A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. Axail loads are…

A:

Q: 1. A vertical column with pinned ends is subjected to an end load P. The column has a radius of…

A: Given that, Radius of gyration of column, k=150 mm,Cross-section area, A=0.02 m2Modulus of…

Q: Stepped bar ABC is fabricated out of aluminum and supported by a fixed support at C as shown. The…

A:

Q: A solid round bar of diameter 250mm has a tensile force of 0.2kN acting on it. What is the stress…

A:

Q: M Two tempered-steel bars, each in thick, are bonded to a -in mild-steel bar. This compolite bar is…

A: The residual stress in the tempered steel bars. Given: The thickness of the tempered steel bars is…

Q: An AISI 1020 steel rod 22 feet long is anchored between two rigid supports. At 90 degrees Fahrenheit…

A: For AISI 1020 steel rod, E=29000 ksi=29×106 psi and α=6.5×10-6 in/in.°F. Let Ti be the initial…

Q: designed to carry on axial compressive load of 400 kN. Using allowable stresses of oco= 6 Mpa and…

A:

Q: An aluminum rod length of 1.0 m and cross-secrional area 0.0005 m2 is used to support a load of…

A: Calculated stress on the aluminum rod. length of 1.0 m and cross-secrional area 0.0005 m2 is used to…

Q: If a 10kN load is applied on steel rod of diameter 10mm , the normal stress will be

A: Normal stress is a measure of the internal forces experienced by a material, such as a steel rod,…

Q: A circular rod of hot-rolled 4340 steel (4340-HR steel - 4mm diameter, 1.35m long) is subjected to a…

A: Given Data:- 4340 Steel  Diameter=4mm Length=1.35m Modulus of Elasticity=207Gpa Yield-Strength…

Q: 1. A steel pipe of length 4 ft, outside diameter of 6.0 in., and inside diameter of 4.5 in., is…

A:

Q: A column is made of the two materials side by side as shown. Each material carries a portion of the…

A:

Q: I need to solve this question

A: Write the given information.

Q: An engineering machine component operating in a high temperature environment consists of a copper…

A:

Q: A bronze square wire 6.5 m. long is hanging vertically and supports a tensile load of 281 KN.…

A:

Q: 1. A hollow steel tube of external diameter 100mm and a wall thickness 12mm is subjected to an axial…

A:

Q: A copper tube having a cross-sectional area of 2000 mm2 and a length of 300 mm is placed between two…

A:

Q: A composite rod is comprised of an EN8 steel shaft of length, diameter and Young’s modulus of 200…

A: The schematic diagram of the given composite rod:- Given data, Length of steel rod, L1 = 0.2 m…

Q: A steel rod of 30 mm diameter is subjected to a 10 kN of axial load. The length of the steel rod is…

A:

Q: 0 kN. Determine the required cross-sectional area of the wable stresses are 6 MPa for concrete and…

A: Need to determine the cross-Sectional area of reinforcing steel

Q: A diagonal aluminum alloy tension rod of diameter d and initial length / is used in a rectangular…

A: The given data  d=0.55in l=7.4ft Allowable stress = 21 kpsi  Find the stretch in rod

Q: 3. Bars AB, CD, and EF cach have a cross-sectional area of 25 mm and modulus of clasticity E=200…

A:

Q: A steel rod of length 10 m is subjected to a axial load of 10 kN. Calculate the elongation of the…

A: Given data  Length of steel rod (L) = 10 m  Axial load (P) = 10 kN diameter (d) = 40 mm E = 200 GPa…

Q: Rigid member AC is supported by a pin at A and the vertical steel link BD as shown. The diameter of…

A: σBD=200 MPaLbd=48 mmhbd= .95 ma Now link BD σBD=P1AP1=200×π4×482P1=361.911 KNNow taking moment…

Q: A hallow cylindrical steel column with an outer diameter of 200 mm and an inner diameter of 180 mm…

A:

Q: The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of…

A:

Q: A rope has a cross sectional area of 0.002m2 and is being used to lift a 5000N weight. What is the…

A:

Q: Pmax: i kN

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.