Q6. The thin plate with four holes as shown in Figure Q6 has a mass per unit area of 33 kg/m². The radius r for each hole is 50 mm. The thin plate has the dimension of 400 mm x 400 mm and suspended at pin at A. (a) Calculate the mass moment of inertia of the thin plate with four holes about an axis passing through its mass centre G, IG.

Q6. The thin plate with four holes as shown in Figure Q6 has a mass per unit area of 33 kg/m². The radius r for each hole is 50 mm. The thin plate has the dimension of 400 mm x 400 mm and suspended at pin at A. (a) Calculate the mass moment of inertia of the thin plate with four holes about an axis passing through its mass centre G, IG.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.87RP

See similar textbooks

Similar questions

Compute the principal centroidal moments of inertia for the plane area.
Using integration, compute the polar moment of inertia about point O for the circular sector. Check your result with Table 9.2.
find the moment of inertia of a quarter of a hollow disk (shaded part of the figure), of inner radius a and outer radius b, of mass M and surface mass density that grows linearly as one moves away from the center of a disk. The axis about which to measure the moment of inertia passes perpendicularly through the center of the hollow disk.
Consider Figure Q3. Determine the mass moment of inertia of the composite body about the ? and y axes. Mass of rod = 2 kg/mMass of disc = 15 kg/m2
Consider a wheel of radius r = 0.28 m, with six spokes (or three rods of length equal to the diameter of the wheel). The total mass of the wheel is 3.0 kg and 55% of the mass is evenly distributed on the circumference while the rest is evenly distributed on the spokes. Calculate the moment of inertia. r
Consider Figure Q3, Determine the mass moment of inertia of the composite body about the x and y axes. Mass of rod = 2 kg/m Mass of disc = 15 kg/m2
6. Derive an expression for the moment of inertia of the pictured semi- circular loop-rod device about an axis through the point P, perpen- dicular to the page. The mass of the semicircular loop is 3.14 kg, and the rod is 3.0 kg. Take R = 1.0 m. [24.14 kg m²] 3R
Find the moment of inertia about the z-axis for a constant density 1 circular cone with base radius 7 and height 6, placed so the axis of symmetry is on the z-axis, after a cylindrical hole of radius 2 is drilled through the axis of symmetry.
A homogeneous wire with a mass per unit length of 0.056 kg/m is used to form the figure shown. Determine the mass moment of inertia of the wire with respect to each of the coordinate axes.
Differentiate between the Inertia, Moment of Inertia and Mass Moment of Inertia. Also give at least example of each.
2. The brick shown below is formed by a rectangular prism with three cylindrical holes. The brick has a density of 2000 kg/m³ and a depth (not pictured) of 50 mm. Each cylindrical hole has a diameter of 50 mm. a. Calculate the total mass of the brick. b. Calculate the center of mass of the brick measured from Point O. You may do this by inspection (no work required). Calculate the moment of inertia of the body about an axis into the plane of the page and passing through Point O. C. y O each dim. 50 mm OOO 200 mm 100 mm
Find the moment of inertia about the x-axis of a thin plate with density & = 5 bounded by the circle x +y = 1. Then use your result to find I, and ,- (Type an exact answer, using t as needed.)