Draw the schematic for a logic circuit that will detect when the input is 0, 1, 2, 4, 6, 8, or 9. The input is the 4-bit signal N3:0, which represents the input number. The output of the circuit is called F (for "found"). Your circuit should use 2-level logic and a minimum number of gates. For example, when N30 is 0010, the output F should assert, and so on. Remember to use good schematic practices. Messy, unclear, or difficult to read schematics will lose points.

Draw the schematic for a logic circuit that will detect when the input is 0, 1, 2, 4, 6, 8, or 9. The input is the 4-bit signal N3:0, which represents the input number. The output of the circuit is called F (for "found"). Your circuit should use 2-level logic and a minimum number of gates. For example, when N30 is 0010, the output F should assert, and so on. Remember to use good schematic practices. Messy, unclear, or difficult to read schematics will lose points.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Analyze the logic function of the circuit A₁ B₁ CH D -S₁
What logic function is performed by this circuit? VDD a. O d. e. A b. None OC AB AB A+B A+B O f. B AB M₁ M₂ M3 M4 F M5
Use K-map to simplify the following logic expression and draw the logic diagram:- Y = Ā. B.Č.D + Ā. B.C.D + Ā. B. Č.D + Ā. B.C.D + Ā.B.C.D + A. B.Č.D + A. B.C.D
answer this plss the subject is logic circuitss
INSTRUCTIONS • Create a project, create a VI and Design the logic circuits below. You can create all the circuits in one VI. When done, use the save all function to save the project and the VI. Zip (not RAR) and save the files under your ID and name e.g. 10448989_Matthew_Fiifi_Hayford.zip. 1. F(X, Y, Z) = X + YZ Design the logic diagram below and simulate. Ensure that you get the output as shown in the truth table. X Y Z X+YZ or F 000 001 010 011 100 101 11 111 1 Y 1 1 1 > N
Implement the circuit (draw the schematic) using the different implementation methods for the 4 logic functions b3M2, b2M2, b1M2 et b0M2: b2M2: With a 16 to 1 multiplexer b1M2: With an 8 to 1 multiplexer. bOM2: With a decoder and an OR logic gate. OOOO 0 D D OD 0 D 1 1 1 1 1 1 1 1 OOOOHHH D 1 1 1 0 D D 0 1 1 1 1 OOHHOHHOCHHOOHH 0 0 1 0 1 1 0 1 CHOHO 0 0 1 D 1 0 CHOHOHOHO. 1 0 1 1 1 0 1 b3 M2 0 ONOC 1 0 0 OOOHPCHAT 0 0 0 1 d 0 1 d d 1 1 d 62 M2 0 HOHOC al 0 0 0 FREETROOT d 1 d d 0 0 d b1 M2 0 HOL 0 0 1 0 1 d 1 0 PPO d d HOD 0 d b0 M2 0 1 0 1 1 0 1 0 d 0 0 d d 0 1 d
1. Consider the following two logic circuits. VDD A-6 B-d6 A-6 B-6 -6 -6 F VDD F t t A Circuit A Circuit B a. Do these two circuits implement the same logic function? If yes, what is that logic function? If no, give Boolean expressions for both circuits. b. Will these two circuits' output resistances always be equal to each other? c. Will these two circuits' rise and fall times always be equal to each other? Why or why not?
Logic Equation Y1 : minimum SOP (Y2) The Logic citcuit :
16) For the circuit that is shown in the Figure shown below. LG represent logic circuit with the following function: Y= N1.N2+ (N1+N2) Write a subroutine (subprogram) to implement the function of LG, use this subprogram in main program to find the value of M for the following values: XI=0, X2=1, X3=1, X4=1, X5=1 X1 LG X2 N1 Y LG X3 M N2 Х4 LG X5
2. Sequential circuit shown below has two flip-flops A and B and one input x. It consists of a combinatorial logic connected to the flip-flops, as shown in Figure below. Analyze the circuit: a. Derive the next state and output equations. b. The state table of the circuit. c. Draw the state diagram. A K. 2-t0-1 MUX Y B' CLK
Design a logic circuits w/ 4inputs (A(MSB), B,C,D(L,S,B)) and 1 output x. The 4 inputs represent switches in a vending machine. The switches can be either open (0) or closed (1) The X output becomes high if and only there are two or more switches closed at the same time. Furthermore it is impossible for the first A and the last switch D to be closed at the same time. Reqd: 1.) complete and labeled truth table 2.) canonical sop form expression 3.) grouped kmap 4.) minimum SOP expression
I want to learn how to draw the circuit from the function in the digital logic design lab If she gives me a function how to draw it to a circuit with gates Easy explaining please