Draw the schematic diagram of the problem; The steam used by a turbine is 5.50 kg/kw-hr at a pressure of 4.50 MPaa and a temperature of 373 degree Centigrade. The overall boiler effeciency is 85% with feedwater temperature at 165 degree Centigrade. a) How many kilogram of coal are required per kw-hr if calorific value of coal is 28,000 kJ/kg? b) If coal costs Php 440 per Metric Ton, what is the fuel cost per kw-hr?

Draw the schematic diagram of the problem; The steam used by a turbine is 5.50 kg/kw-hr at a pressure of 4.50 MPaa and a temperature of 373 degree Centigrade. The overall boiler effeciency is 85% with feedwater temperature at 165 degree Centigrade. a) How many kilogram of coal are required per kw-hr if calorific value of coal is 28,000 kJ/kg? b) If coal costs Php 440 per Metric Ton, what is the fuel cost per kw-hr?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pls. Answer this..? A steam engine has 10% brake thermal efficiency and consumes 750 kg/hr steam. The enthalpy of steam at the entrance ang exit of the engine and condenser are 2800 and 450 kj/kg repectively. Determine the brake power of the engine in kw.
Q2: Use dinensional analysis to derive as epresion for the power develaped by an engine in terms of the torpue T and roarive sped u.
4) A gos tubre Ahe orking sebslance Durirg the alort d the compraico,he compression, the pescue d 500LR The conditoo of the atld of tomperahune of gos is at 340k ord ompresskn proces adobalic with geo 650k ond 193OKR. The wotona subatonce le hsted ord entoed the turbine at 1400k ond kzokR ond enronde adiabalically to 900k Ond 490HR. Detrmne: The compresor Ond turbine fictres oe achol compressor ond turbire vork o ho nakd the cyce c Te thond ficey c) Acunng that a domme the w Drow the schonadk dicgrom regoroabr is installed with 85% Hocticnes, thermal ficions
Find the power which a 2.5 MW natural gas engine can develop at an altitude of 1981.2 meters taking into consideration the pressure and temperature change.
Steam enters a turbine at 600 ᵒC at 7300kPa pressure and leaves the turbine as saturated steam at 75 kPa.. Turbine inlet diameter is 50 mm and outlet diameter is 300 mm. In case the velocity at the turbine inlet is 200 m / sFind the turbine output power a) find the heat transfer, ignoring kinetic and potential energy changes. B) kineticsExplain by calculating whether the energy change is negligible.
Thank you
1. An engine from a quarry vehicle used in the Build a Beach program of DEMR has a power requirement of 560 kW. Per hour of its operation, it ejects 234 MJ into its surroundings at 50 °C. If it behaves like a Carnot engine, answer the questions below. A. How much work (MJ) is done by the engine per hour of operation? B. What is the efficiency (%) of the engine?C. What is the temperature (°C) of the hot reservoir? 2. Determine the entropy change (kJ/K) associated to the conversion of 10 kg of ice at -11 °C to steam at 121 °C. 3. Anna and Beth are using another rare metal, the nth metal (c = 0.600 J/g-℃), to build the 5-kg cuirass of their design. Initially, the metal is at 2250 K. It is then submerged to 10 kg of water at 15 °C. If the remaining liquid water after submerging the metal is 8.5 kg, solve for the net entropy change (kJ/K) of the system.
Q.4:A) A single-stage reciprocating compressor takes Ikg/min at 1bar, 288K and delivers it at 5bar calculate the indicated power required and isothermal efficiency, assuming that the law of compression and expansion is PV = C and that the clearance is negligible. B) A certain natural gas has the following volumetric analysis: 60% CH4, 13% H2, 18% CO, 6% CO, and 3% O2. This gas is burned completely with the stoichiometric amount of dry air. Determine the theoretical the air-fuel ratio and the mole fraction of each products.
b) Elaborate the response of pressure to the reservoir fluid properties using suitable equation.
A cylindrical tank 3 m long and 2 m diameter is used for oil storage. How many days can the tank supply the engine having 27oAPI with fuel consumption of 65 kg/hr?
1.) A hand pump is used to inflate a bicycle tire to a gauge pressure of 70 psi. a) How much work must be done if each stroke of the pump is an adiabatic process and what is the final temperature of the gas? b) We inflate the tire in two steps: (i) an isobaric compression and (ii) an isochoric increase in temperature. Calculate the work done by gas/"us" and/or heat added/removed during the two steps! Is this a viable alternative to the adiabtic compression Explain! Atmospheric pressure is 1 atm, the air temperature is initially 25° C, and the volume of the air in the tire remains constant. Useful values: A bicycle tire is 26 in diameter and has a cross-sectional area of 2 in² [1 in = 2.54 cm]. 1 lb corresponds to a mass of 0.445 kg. c) For Take-Home only Solve the questions in a) and b) in terms of the initial pressure P₁ = P*, the final volume Vf = V* and the pressure ratio K = Pf/P*!
Q 1: For a particular gas system, the internal energy is given by : U = 2.5 PV + C , where P: Presure , V: volume and C : constant, the sysytem is taken into cycle shown in fig.(Q1) below with three Processes, Calculate Q & W if the pressure is given by P= 105+ 10° (v-0.02)² ? 05- 0.4 0.3E A 02E 0.1 0.01 002 003 V (m³) -> Fig. (Q1) P (MPa)