Several forces are applied to the pipe assembly shown. Knowing that Q=250 lb and that the pipe has inner and outer diameters equal to 1.61 in. and 1.90 in., respectively, determine the normal and shearing stresses at point H and point K. (Round the final answers to two decimal places.) 22 K 150 lb 6 in. The normal stress at point His The shearing stress at point His The normal stress at point K is The shearing stress at point K is 50 lb ksi. ksi. ksi. ksi. 10 in. e 150 lb

Several forces are applied to the pipe assembly shown. Knowing that Q=250 lb and that the pipe has inner and outer diameters equal to 1.61 in. and 1.90 in., respectively, determine the normal and shearing stresses at point H and point K. (Round the final answers to two decimal places.) 22 K 150 lb 6 in. The normal stress at point His The shearing stress at point His The normal stress at point K is The shearing stress at point K is 50 lb ksi. ksi. ksi. ksi. 10 in. e 150 lb

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Re Several forces are applied to the pipe assembly shown. Knowing that Q= 250 lb and that the pipe has inner and outer diameters equal to 1.61 in. and 1.90 in., respectively, determine the normal and shearing stresses at point Hand point K. (Round the final answers to two decimal places.) 150 lb 10 in. 4 in. 150 lb 6 in. 50 lb 4.79 O ksi. The normal stress at point His The shearing stress at point H is 83.63 -41 ksi. ksi, The normal stress at point K is 3.83 O ksi. The shearing stress at point K is
In the figure shown, assume that a 21.3-mm- diameter rivet joins the plates that are each 118 mm wide. The allowable stresses are 119 MPafor bearing in the plate material and 54 MPa for shearing of the rivet. Determine the minimum thickness of each plate. (Answer must be in millimeters) P P W mm d-mm Ø Round your answer to 2 decimal places. P. P.
A 7/8-in.-diameter steel rod AB fitted to a round hole near end C of the wooden member CD. A shearing stress of 145 psi acts on the surfaces indicated by the dashed lines. a. Determine the maximum normal stress (in psi) in the wood. b. Determine the distance b (in inches) for which the shearing stress is applied. Round off to a whole number. c. Determine the bearing stress (in psi) between the steel rod and the wood.
Determine the maximum shearing stress in a bronze helical spring composed of 19 turns of 0.96-in.-diameter wire on a mean radius of 3.53 in. when the spring is supporting a load of 516 lb. Use the equation for heavy spring and G = psi. (Answer must be in lb per square inch) Round your answer to 2 decimal places.
5 decimal places 1. Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 51 kN if it developed a stress of 21 MPa. Take note that the inner diameter is 3/6 of the outer diameter. 2. Three identical plates of 67 mm wide and 7 mm thick is connected by a square pin with side dimension 17 mm. If the middle plate is subjected to a tensile force of 25 kN, determine the shear stress (MPa) developed in the pin. 3. Two identical plates of 61 mm wide and 5 mm thick is connected by a square pin with side dimension 19 mm. If a plate is subjected to a tensile force of 28 kN, determine the bearing stress (MPa) developed in the plate.
Answer the following problem. Show your complete solution. Use 4 decimal places. 2. Two shaft of diameter 50 mm are joined by a rigid flange coupling and transmit a torque in such a way that the shear stress in shaft does not exceed 100 N/mm2. If six bolts are used to join the flange and the bolt circle is 150 mm in diameter. Determine the diameter of the bolt if the permitted shear stress in the bolt is 80 N/mm2.
For the state of stress shown, it is known that the normal and shearing stresses are directed as shown and that σx = 14 ksi, σy = 9 ksi, and σmin = 5 ksi. a) Determine the orientation of the principal planes. (Round the final answers to one decimal place.) b) Determine the principal stress σmax and the maximum in-plane shearing stress in ksi. (Round the final answers to two decimal places.) c) On paper, show the properly oriented elements representing: i) the principal planes, and ii) the planes of maximum shear stress.
Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a diameter of 0.8 in. Take P = 2000 lb. 2.5 in. 600 lb max The principal stresses are: ksi 1 in. Determine the principal stresses and the maximum shearing stress at point H. (Round the final answers to two decimal places. Input the answers with the appropriate sign.) A 3.5 in Omin ksi The maximum shearing stress is ksi,
One of the principal stresses in a two-dimensional stress system is 139 N/mm² acting on a plane A. On another plane B normal and shear stresses of 108 and 62 N/mm², respectively, act. Determine a. the angle between the planes A and B, b. the other principal stress, c. the direct stress on the plane perpendicular to plane B. Ans. (a) 26°34', (b) –16 N/mm², (c) 15 N/mm².
The grain of a wooden member forms an angle 15° with the vertical. For τxy = 245 psi, determine the in-plane shearing stress parallel to the grain and the normal stress perpendicular to the grain. (Round the final answers to one decimal place.)
Q1/ For the state of plane stress shown below, construct a Mohr's circle and determine:- (a) the principle stress acting at this point (b) the orientation of the principle stress (c) the maximum in-plane shear stress at the point and the corresponding average normal stress (d) the orientation of the maximum in-plane shear stress (e) show the results on elements 700 kPa 100 kPa tal stress enks 400 kPa
Q1/ For the state of plane stress shown below, construct a Mohr's circle and determine (a) the principle stress acting at this point (b) the orientation of the principle stress (c) the maximum in-plane shear stress at the point (d) the orientation of the maximum in-plane shear stress (e) show the results on elements 30 kPa 80 kPa