Q3. Determine the dimensions of an I-section connecting rod for a petrolengine from the following data:Diameter of the piston = 110 mm; Mass of the reciprocating parts = 2 kg;Length of the connecting rod from centre to centre = 325 mm; Strokelength = 150 mm; R.P.M. = 1500 with possible over speed of 2500;compression ratio = 4 : 1; Maximum explosion pressure = 2.5 N/mm.

Answered: Image /qna-images/answer/66b9c47a-90eb-4104-bbf3-eb314608e946.jpg

Determine the dimensions of an I-section connecting rod for a petrol ne from the following data: neter of the piston = 110 mm; Mass of the reciprocating parts = 2 kg; gth of the connecting rod from centre to centre 325 mm; Stroke th = 150 mm; R.P.M. = 1500 with possible over speed of 2500; pression ratio = 4 : 1; Maximum explosion pressure 2.5 N/mm2.

Determine the dimensions of an I-section connecting rod for a petrol ne from the following data: neter of the piston = 110 mm; Mass of the reciprocating parts = 2 kg; gth of the connecting rod from centre to centre 325 mm; Stroke th = 150 mm; R.P.M. = 1500 with possible over speed of 2500; pression ratio = 4 : 1; Maximum explosion pressure 2.5 N/mm2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2 An automotive engine has a bore of 90 mm; the stroke is 110 mm; and the length of the connecting rod is 166 mm Knowing that the volume of the combustion chamber is 75 cm³ and the intake valve closes 18° crank angle degree after BDC. If injection Started 10 degrees before TDC and ends 40 degree after TDC. And the engine is running at 3000 rpm. a. Calculate the geometrical compression ratio and the actual compression ratio? b. Find the ratio between the maximum speed of the piston to the mean piston speed for this engine? c. Find the injection period
(2) a fou-cylinder, 2.4 liter engine operates on a four-stroke cycle at 3200 r.p.m. the compression ratio is 9.4:1, the connecting rod length r = 18 cm, and the bore and stroke are related as S = 1.06 B. calculate :- 3 (a) clearance volume of one cylinder in cm³,L, and in ³. (b) Bore and stroke in cm and in. (c) Average piston speed in m/seca 1 ft/sec
. Two identical cylinders are applied in series as shown in Fig.2. The cylinder piston and rod diameters are 80 mm and 40 mm respectively. The valve is working in position 2. Assuming the tank pressure is 1Bar. . In order to lift the mass 3000 kg in velocity of 0.1m/s, how much pressure in MPa are needed from the motor? • How much volume in liter/min are needed from the motor? 24p CA. ZAP Tips: Q=C₂4 P2 A2 P1 A1 A2 A1 Q1 Q2 MIHIXM Q3
A four-cylinder, 2.4-liter engine operates on a four-stroke cycle at 3200 rpm. The compression ratio is 9.4:1, the connecting rod r = 18cm, and the bore and stroke are related as S = 1.06B Calculate: (1) Volume in the combustion chamber when crank angle at 90 degrees (2) Clearance volume of one cylinder in cm³, L, and in3 (3) Bore and stroke in cm and in (4) Average piston speed in m/sec and ft/sec
2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW find the following: fuel consumption m'f = kg/ sec the air consumption engine capacity.: the flow rate of air intake to cylinder the Volumetric efficiency
As shown in Fig., the working area of cylinder head side A=50cm", working load F=10000N, the setting pressure of the valve 1 is 5MPA, and the setting pressures of the valve 2 is 3MPA. e Please answer the following questions: 1) What's the pressure at point A and B respectively when piston of the cylinder is moving forwards at the working speed. Please give the reason. 2) What's the pressure at point A and B respectively when piston of the cylinder reaches and stops at the end. Please give the reason.e To system F A B
2.5-L bench scale bioreactor is used for the production of recombinant P64K protein from Neisseria meningitides. The dimensions for the bioreactor are Dt 12.9 cm, ratio Di/Dt = 1/3 and N = 700 rpm. With the scale up factor of 2.24, determine the impeller tip speed (m/s) for the pilot scale bioreactor based on constant impeller tip speed and constant power consumption per volume. Predict which scale up method might give a higher concentration of P64K, if the demand of dissolved oxygen plays an important role.
A four-cylinder, 2.4-liter engine operates on a four-stroke cycle at 3200 RPM. The compression ratio is 9.4:1, the connecting rod length r= 18 cm, and the bore and stroke are related as S = 1.06B. (a) clearance volume of one cylinder in cm³, (b) bore and stroke in cm, (c) average piston speed in cm/sec. (d) the piston speed when the crank angle 0 = 90° aTDC? (m/sec)
There are two double-acting pneumatic actuators, the extension of each one is executed in 5 seconds at 80 psi and recoil in 4 seconds at 30 psi, the travel of both is 12 inches, the diameter of the piston is dp = 4 "and of the rod dv = 1"a) Determine the compression ratios. The local atmospheric pressure is 79kpa = (11.5 psi)b) Determine the air consumption in cubic feet per minute of free air PCMc) Determine the average air consumption for each.d) Propose the regulation values of the pressure switch, system pressure and safety valve
The Stroke of a gas engine which works on the constant volume cycle is 412 mm. The pressure at the beginning of the compression is 2.22 bar and at the end of compression is 14.04 bar. Assuming compression follows the law PV^1.36 = C, Calculate the clearance between the piston and cylinder cover at the end of compression in mm of length.
Q3: You are designing a four-stroke cycle diesel engine to provide a brake power of 300 kW naturally aspirated at its maximum rated speed. Based on typical values for bmep and maximum mean piston speed, estimate the required engine displacement, bore and stroke for sensible cylinder geometry, also find the number of engine cylinders. What is the maximum rated engine speed (rev/min) for your design? What would be the brake torque (N-m) and the fuel flow rate (g/hr) at this maximum speed? Assume a maximum mean piston speed of 12 m/s is typical of good engine designs.
The pressure ratio during the constant volume portion of combustion in a Dual Combustion engine is 1.89 . If the pressure at the end of the constant volume addition of heat is 4.49 , what is the pressure at the beginning?