FIG. P2.91 10 in. 5. The aluminum and bronze cylinders are centered and secured betwcen two ngid end-plates by tightening the two steel bolts. There is no axial load in the as- sembly at a temperature of S0 F. Find the stress in the steel bolts when the 1emper- ature is increased to 200 F. Use the following data Alericn Booaze A (in.) a i F) E (psi) Aluminum cylinder 2.00 12.8 x 10 10 10° Bronze cylinder 3 00 105x 10 12 10° FIG. P2.92 Each steel bolt 0.75 6.5 x 10- 29 10°

Q: answer is 900.8 please resolve

A: Given Data

Q: This still doesnt answer how to get points 2,  2', and 1', so how did you get it?

A: Itis asked to explain how the state points 2, 2' and 1' are obtained

Q: Given the top and front view create a section view.

A: Find Create a section view using the given top and front views.

Q: Consider an air-standard Diesel cycle. Operating data at principal states in the cycle are given in…

A:

Q: Given the isometric drawing, draw the multiview projection. The multiview projection of the glass…

A: Draw the isometric view.

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Given:Find:Draw the lines corresponding between the views.

Q: Please look at pic. Please help, I don't get part b. Thanks

A:

Q: solve both

A: Power input, Gear speed of input shaft, Gear ratio, Power loss,

Q: INSTRUCTIONS: Solve for all unknowns (magnitude and direction). A 10' 300# 10' 150# B 5'

A: According to the given data A beam  AB is given  We need to find Reaction  at point A and B

Q: Answer in number 7 and 8.

A:

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: This is no answer sorry the answers are offered A B C or D

A:

Q: Draw velocity polygon.

A: Solution:

Q: 1500# 1500# 1500# 1500# 12' K I

A: In this problem, following steps will be taken 1. Determine the reactions at the supports.' 2. Using…

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: You are designing a new engine; this device operates with liquid fuel as an input and gener energy…

A: Hello. Since you have posted multiple questions we will solve the first question for you. If you…

Q: The other part of the question is not solved please look at it

A: Normal stress in the x direction, Normal stress in the z-direction, Shear stress in the x-z plane,…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: now please answer question 2 and 3 please

A: This question is based on the concept material science. As per the guidelines we are subjected to…

Q: the isometric drawing has to be in 30 degree angle or vertical

A: It is asked to describe whether the isometric drawing has to be at 30 degree angle or vertical

Q: Using just a yardstick or a measuring tape, open the classroom door 35 degrees. You cannot use a…

A:

Q: A projectile is shot from the top of a building 96 ft high from a gun at an angle of 30° with the…

A:

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: axis of the solid. Draw its projections, sectional front view & true shape of the section. Also…

A:

Q: What is the worst-case distance between the bottom surface of the slot and the botto surface of the…

A: Given drawing

Q: Solve both and show all parts and solutions

A: The power to input shaft is The speed of gear of input shaft is The gear ratio is The loss in power…

Q: Question 3) On the  plate in the figure, the length  L  is given as L=72 m . According to this;…

A:

Q: Drive Shaft Outlet Blades Inlet Scroll Impeller

A: IMPELLER FAN A fan impeller is ordinarily joined to the turning shaft. Outer rotor engines basically…

Q: 3. Water is flowing in a pipe with radius of 25.4 cm at a velocity of 5m/sec at the temperature in…

A:

Q: TOP FRONT SIDE

A: GIVEN DATA ISOMETRIC VIEW GIVEN WE HAVE TO DRAW ORTHOGRAPHIC VIEWS OF GIVEN FIGURE

Q: Give a steps by steps answer of the solution

A:

Q: Problem A solid uniform ball with mass m and diameter d is supported against a vertical frictionless…

A:

Entropy

In physics, entropy means the amount of disorder or the degree of randomness associated with a thermodynamic system. The system is not self-organized when the entropy of the system is high. For instance, when a system is at an elevated temperature, its molecules are in random motion, vibrating and colliding with each other. During this scenario, the probability of finding a molecule at a particular place twice, is low. Under this circumstance, the system can be said to be in a high entropy.