dave connects an electric circuit to find the resistance of 100 cm of wire. the battery voltage is 9V. the ammeter is 2A. and the voltmeter is 5V. what is the resistance of the 100cm of wire 2012 Dave connects an electric circuit to find the resistance of 100cm of wire.Look at the diagram below.9V100 cm of wireThe battery voltage is 9V.The reading on the ammeter is 2A.The reading on the voltmeter is 5V.(a) Calculate the resistance of the 100 cm of wire.(b) Dave now uses some thinner wire.A 100 cm length of this wire has a resistance of 5 ohms.What length of this wire is needed to mako a 2 ohm resistor?

The given circuit is shown below: Voltmeter reading:V=5 voltAmmeter reading:I=2A

Answered: dave connects an electric circuit to…

dave connects an electric circuit to find the resistance of 100 cm of wire. the battery voltage is 9V. the ammeter is 2A. and the voltmeter is 5V. what is the resistance of the 100cm of wire

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter12: Batteries And Other Sources Of Electricity

Section: Chapter Questions

Problem 14RQ: 14. A 6-V lead-acid battery has an A-hr rating of 180 A-hr. The battery is to be load-tested. What...

See similar textbooks

Related questions

Q: (ii) Find the magnitude and direction of the unknown currents in figure 3. Given il = 10A, i2 = 6A, ...

Q: How did you get the I1A and 12A answer pls need the solving thanks

Q: 1 out of 3 attemp Find the bandwidth and center frequency of the bandstop filter of the figure. Roun...

A: Given circuit,

Q: tance total Impedanee total Capaci

A: Inductance is series- Leq=L1+L2+......Inductance in parallel-1Leq=1L1+1L2+...... Capacitance in para...

Q: A 440 V, 3-phase a.c. motor has a power output of 11.25 kW and operates at a power facror of 0.8 lag...

Q: Power rating of a motor drawing a current of 40 A at 400 V is?

A: Given: A motor drawing a current, I = 40 A At voltage, V = 400 V

Q: When would you use a pressure transducer coupled to an oscilloscope?

A: Pressure Transducer: Pressure transducer is an instrument which converts an applied pressure into a...

Q: A 46-mH inductive coil has a resistance of 10 ohms. How much current will it draw if connected acros...

A: Given a Inductive coil with resistance having, Inductance, L = 46 mH Resistance, R = 10 ohms Supply ...

Q: If the power factor is 1/10 and the value of impedance is 20 ohm, calculate the resistance in the ci...

A: Given, Power factor, cosϕ=110 Impedance, Z=20 Ω

Q: 4. Two parallel plates, connected to a 200-V power supply, are separated by an air gap. Ho- small ca...

A: Note: As per the guide lines of the bartleby we are supposed to solve one question, when they are ...

Q: In case of 625-B television standard the maximum frequency deviation should not exceed ± 50 kHz. Cal...

Q: Determine the magnitude of the series impedance parameters of Transformer(Req ,Xeq) referred to the ...

Q: 2.A three-phase, three-wire system, with an effective line voltage 100 V, has currents IA Ic = 15.41...

A: This question belongs to electrical power system . It is based on the concept of delta connected bal...

Q: Use source transformation to find Vo in the circuit shown. 10 ww. 05V, 20 ww 10 V 2A 42

A: Given circuit shown

Q: Use a 4-to-10 line decoder achieve the following functions, fi(a, b, c, d) %3 т, + mз + ms f-(a, b, ...

Q: When the load impedance is equal to the characteristic impedance of the transmission lines, then the...

A: Calculation of reflection coefficient and standing wave ration, of the transmission lines when the ...

Q: The following is configured on a router Router(config)# interface g0/0.10 ...

A: On a router - The following instructions is set up, Router(config)# interface g0/0.10 Router(config-...

Q: A copper wire having a diameter of 0.80 mm is measured to have a resistance of 10.3 Ω at 20 o C. How...

A: This question belongs to circuit theory . It is based on the relation among resistance , length , ar...

Q: A diode is not yet fully forward biased (Vp=0 3V) so there is only a small amount of current The sat...

Q: xplain the essential features of Indicating Instruments Please do not write the answer on a ...

A: Indicating Instruments - An indicating instrument is simply a movable mechanism pivoting on jewel r...

Q: Determine the capacitance and voltages (Vrms) across the resistor and capacitor and prove that the p...

Q: In the circuit shown in Figure, find its Vrms (gen) and inductive reactance. After that, solve for i...

Q: 8.What is the coefficient of coupling of two coils whose mutual inductance is 1 H and whose self-ind...

Q: What kind of circuit is shown in the figure? Q16Fig1.gif O 1.Low-pass filter O 2.High-pass filter O3...

A: In circuit 1 capacitor is in series with resistor and output is taken from resistor Hence given cir...

Q: VIII) Find (iv) 1011011010.102 by 11012 Please write the steps for the solution

Q: A generating station has a demand of 25 MW, a load factor of 60%, then the average demand will be:

A: Given: A generating station has, Maximum demand = 25 MW Load factor = 60 % Average demand =?

Q: Vcc 6. Find Vo. (Use re model) Rc Ic 240 k Ohm Vo 6 mA 10 mv B=120 ro=50kohms 40uA 2.2 k Ohm 16 V2 V...

A: We need to find out output voltage for given circuit

Q: 2. Identify the location and summarize the purpose of each of the following: а. Piezoelectric elemen...

A: Here it is asked to identify the location and the purpose of each of the given elements. So weed to ...

Q: (1) Three point charges lie along a straight line as shown in the figure, where q, = 6.00 uC, q2 = 1...

A: We have given Three point charges lie along a straight lineq1=6.00μCq2=1.50μCq3=-2.00μCThe separati...

Q: find all current flowing through each resistors

Q: Write a Boolean expression for the output of the logic circuit. #1: z=1 z #2: z=xy+w #3: z=xy+y+w #4...

A: Given: Logic circuit,

Q: 3. Determine the voltage across R2 for the first and second diode approximations. Diode: Si, r = 10 ...

Q: Four electricians are discussing wiring under raised floors in information technology equipment room...

A: "Control" for the disconnecting means should be gathered, labelled, and placed near the main exit do...

Q: Y(s RO) Et

A: Given Signal flow diagram shown

Q: A coil of wire of resistace 50 ohm is embeded in a block of ice. What is the amount of ice melted in...

Q: Explain about controlling torque using Spring control method. Please do not write the answer in a p...

A: Controlling Torque The control device is a device that is used to control the deflection of the poin...

Q: 3-phase induction motor is running at 2% slip. If the input to rotor is 1000 W, then mechanical powe...

Q: The circuit is at a steady state at time t = 0 in Fig. 4. For t> 0, determine the inductor current a...

Q: a. For the network below, determine lg, Ic. VE and VCE

A: The required parameter for the given voltage divider bias circuit can be calculated by using the DC ...

Q: a. A system is provided in Block Diagram form as shown in figure 4, draw its equivalent system in Si...

A: The given block diagram can be reduced by considering the parallel connected and cascade connected f...

Q: first order system,

A: Laplace transform of- ut=1se-atut=1s+a

Q: Use nodal analysis to determine the node voltages in the circuit shown. 4 S 3i. 1s V2 1s V3 2 A 2S 4...

A: The solution is given below

Q: ) Using the information provided in Figure 2, find the branch resistors R1 and Rs, the total resista...

Q: I. Solve for all current and the voltage values across each component. 20n 402 240V, Is MF 5oHz SomH...

Q: Provide your complete solution and formula. Sample Problem: [ EE Board October 1999 | The instantane...

A: According to the given question, it is required to find the rms Voltage for the below given instanta...

Q: Q3/ A- Design a logic circuit using only NOR gates to implement: F(A,B,C)= (A+B+C)(A+B+C)?

A: The given boolean function is shown below: FA,B,C=A+B+CA+B+C

Q: 1. Three impedances of 10453.13°N are connected in delta to a three-phase, CBA system with an affect...

Q: Two resistors 5 kQ and 20 k2 are at 27°C. Calculate the thermal noise power for a 10 kHz bandwidth f...

A: R1 = 5k R2 = 20 k T =temperature= 27°C = (27 + 273) K = 300K B = Bandwidth= 10 kHz

Q: A band pass filter is to be constructed using RC components that will only allow a range of frequenc...

Q: 13. Find Vo if VDs = 9V. %3D 10 uF 10mv 1 M Ohm

A: Biasing- Biasing is an activity of providing DC supply to the circuit.

Concept explainers

Electrical Heating Unit

The conversion of electrical energy to heat energy is known as electric heating. The heating system that converts the electrical energy to heat energy for various application is called electrical heating unit. Electricity is employed as the firing mechanism in electric heating systems, which transforms electric current to heat. Electric heaters have heating elements in the form of electric resistors.

Question

dave connects an electric circuit to find the resistance of 100 cm of wire. the battery voltage is 9V. the ammeter is 2A. and the voltmeter is 5V. what is the resistance of the 100cm of wire

20
12 Dave connects an electric circuit to find the resistance of 100cm of wire.
Look at the diagram below.
9V
100 cm of wire
The battery voltage is 9V.
The reading on the ammeter is 2A.
The reading on the voltmeter is 5V.
(a) Calculate the resistance of the 100 cm of wire.
(b) Dave now uses some thinner wire.
A 100 cm length of this wire has a resistance of 5 ohms.
What length of this wire is needed to mako a 2 ohm resistor?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the figure the ideal batteries have emfs ɛ1 = 20.4 V, ɛ2 = 9.05 V, and ɛ3 = 5.40 V, and the resistances are each 2.40 Q. What are the (a) size and (b) direction (left or right) of current i,? (c) Does battery 1 supply or absorb energy, and (d) what is its power? (e) Does battery 2 supply or absorb energy, and (f) what is its power? (g) Does battery 3 supply or absorb energy, and (h) what is its power? (a) Number i Units (b) (c) (d) Number i Units (e) (f) Number i Units (g) (h) Number i Units
3. The figure on the left below shows a schematic diagram of a battery. The voltage measured by U1 is called the terminal voltage given R1 = 1 ohm. In the figure on the right below, the terminal voltage of each of the battery-resistor combination is Vr = 1.5 volts. Find the following: a. The current passing through R5. b. The currents passing through R1 and R3 C. The voltage across R1. d. The voltage of the battery EMF. e. The percentage of voltage loss ot the battery due to the internal resistance R1. The power dissipated by the internal resistance R1. g. The power dissipated by R5 if R1 = R2 = R3 = R4 = 0. h. The percentage of power dissipation loss due to the four resistors R1, R2, R3, and R4 f. R1 R3 S10 R1 U1 1.500 EMF EMF R5 100 V1 R2 $10 EMF R4 EMF EMF
A resistor has a resistance of 20 ohms at 30 degrees Celsius and 32 ohms at 90 degrees Celsius. Find its resistance at 125 degrees Celsius. Determine also the temperature coefficient at 100 degrees Celsius. (Please Show Complete solution and write properly) (Round off the final answer to the 4th decimal if possible and box the final answer)
Four cells each of 2.10 volt internal emf are parallel connected together to make a battery. The internal resistances are 0.004, 0.005, 0.003 and 0.0025 ohm. Calculate for parallel connections: (a) internal emf and resistance of the single equivalent cell (b) current for a terminal voltage of 1.95 volts, (c)current in each cell
What are the factors that affects or influence the electrical properties of a material? c) Two of you have been given two instruments with the units in ohms, your colleague measures the resistivity of the material whiles you measure the resistance. Your supervisor comes around and ask you to comment both measurements, what would you tell him?
Give a detailed description of an expirment about 'D'Arsonval Meter Movement as DC ammeter'.Support your answer with pictures and examples.
Look for Requivalent(Equivalent Resistance).Please show details
In the figure below you see the sketches for the front and back of an electrical circuit board. The board is cut into a trapezoidal shape and is made of plastic. On the back of the board there is conductive paint shown here in green. On the front there are some resistors and capacitors, in addition to terminals for inserting the leads from a DC power supply. The legs of the resistors and capacitors go through the holes on the board and are soldered to the conducting paint on the back side. You also have a multi-meter which you can use as an ammeter or a voltmeter. 16 v 4700 16 10 8 O- 7 3. 6. 4 O+
What are the differences between load resistance in a circuit and internal resistance in a battery? Explain.
An aluminum wire 5m long and 2mm diameter is connected in parallel with a copper wire 3m long. The total current is 4 A and that in the aluminum wire is 2.5 A. Find the diametre of the copper wire. The resistivity of copper wire being 1.7 micro ohm meter and that of aluminum taken Al 2.6 micro ohm meter
In the figure the ideal batteries have emfs &₁ = 18.4 V, E2 = 9.96 V, and 3 = 4.70 V, and the resistances are each 2.10 Q. What are the (a) size and (b) direction (left or right) of current i₁? (c) Does battery 1 supply or absorb energy, and (d) what is its power? (e) Does battery 2 supply or absorb energy, and (f) what is its power? (g) Does battery 3 supply or absorb energy, and (h) what is its power? (a) Number i (b) (c) (d) Number (e) (f) Number (g) (h) Number 18, www Units Units Units Units =1&₂ <
8.) Suppose a resistor has a voltage drop of 0.000034 volts across it. How many µ (micro) volts is dropped across the resistor? a. 34 µV b. 0.34 µV c. None of These d. 3.4 µV 10.) How much current flows in a short circuit? a. About 2 A b. A very large amount c. A very small amount d. About 20 A 11.) How much resistance is in the following circuit: (picture inserted below) a. A very small amount b. A very large amount