D.C. Supply Voltage Field Current, IF (A) 3.5 V Load Torque, T = 0 N.m. Shaft Speed, Nm (rpm) 662 5322 2.5 1.5 1 0.5 683 800 908 1102 1493 2253 Plot graphs of: Speed, Nm vs field current, IF. ⚫ Efficiency vs Load Torque. Show a sample calculation of efficiency. (Hint: The value of IF to be used in the calculation of the efficiency is the maximum value obtained).

D.C. Supply Voltage Field Current, IF (A) 3.5 V Load Torque, T = 0 N.m. Shaft Speed, Nm (rpm) 662 5322 2.5 1.5 1 0.5 683 800 908 1102 1493 2253 Plot graphs of: Speed, Nm vs field current, IF. ⚫ Efficiency vs Load Torque. Show a sample calculation of efficiency. (Hint: The value of IF to be used in the calculation of the efficiency is the maximum value obtained).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find all types of power losses (the second photo shows the types of power losses) The weight of the car is 800 Kg The weight of each person is 75 Kg You may assume any missing parameters you need in the design appropriately (e.g., the rolling-resistance-power, air-resistance-power, the DC motor's parameters, ....etc)
Find the rolling force and its power. The weight of the car is 800 Kg The weight of each person is 75 Kg You may assume any missing parameters you need in the design appropriately (e.g., the rolling-resistance-power, air-resistance-power, the DC motor's parameters, ....etc)
The resistance of the field winding(copper wire) of a DC machine is 0.25 ohm at 25°C. When operating at full-load, the temperature of the winding is 75 °C. The temperature coefficient of resistance of copper is 0.00427 per °C at 0°C. Find the resistance of the field winding at full-load.
• A DC shunt machine while running as generator develops a voltage of 250 V at 1000 r.p.m. on no-load. It has armature resistance of 0.5 ohm and field resistance of 250 ohm. When the machine runs as motor, input to it at no-load is 4 A at 250 V. Calculate the speed and efficiency of the machine when it runs as a motor taking 40 A at 250 V. Armature reaction weakens the field by 4 %
A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 220 V (RMS), 50 Hz. The delay angles of both thyristors are set to 90 degrees. The maximum power that can be delivered to the load is: Select one: a. 5.65 kW b. 9.68 kW c. 11.52 kW d. None of these
Get the electromechanical analog model (torque-voltage or torque-current) of the system. With all the steps of the analysis
A250 V, dc. shunt mtor has an amature resistance of 0.5 chmand a field resistance of 250 dhm When driving a load of canstant tarque at 600 r.pm, the ammature current is 20 A If it is desired to raise the speed fram600 to 800 r.p.m, what resistance should be inserted in the shunt field circut? Assume that the magnetic circut is unsaturated
The armature and field resistances of a series machine are 0.2 ohm and 0.3 ohms respectively. While running as a generator, the generated emf is 250V at 1200rpm. If the machine is run as motor, it takes 4A at220V. At a certain load, the motor takes 30A at 220V. However, on load, the armature reaction weakens the field by 4%. Find the motor speed at this load.
Verify the following property of the twiddle factor:
Find the values of input and output power. The weight of the car is 800 Kg The weight of each person is 75 Kg You may assume any missing parameters you need in the design appropriately (e.g., the rolling-resistance-power, air-resistance-power, the DC motor's parameters, ....etc)
The electrical equivalent of mechanical load in induction machine is......................... a. Rr/s b. Rr/(1-s) c. Rr d. Rr*(1-s)/s
A thicker wire is used in the DC series field winding than DC shunt field winding in DC machines. * O because it carries the load current. O to prevent mechanical vibrations. O to provide strength. O to produce large flux. The speed of a DC motor can be changed by varying - armature resistance circuit O flux per pole O voltage source O all of above