An RLC series resonance circuit has a resonance frequency of (5000/2π) Hz and impedance at resonance is 56 Q. Find the value of the inductance if the Q-factor is 25.
Q: How would you design an 125 ohm microstrip transmission line?
A: Designing a 125 ohm microstrip transmission line involves determining the physical dimensions and…
Q: Find V (s) in the following circuit. 0.25 H m 3V₂ 0.2 F 10 Ω ww Vx + 5e-2t u(t) V
A: I have written this solution as handwritten solution. Hope you find the solution clear.
Q: QUESTION 12 L1 Inputs o-S1 0-S2 0-S3 0-S4 o-S5 2 3₂ 4 Ladder logic program S1 PL3 36 S3 H S5 36 10…
A: Given a ladder logic program When all the switches are turned on in order according to the following…
Q: Compute the resistivity of the given material whose resistance is 2 Ω; area of cross-section and…
A: I'm this question We need to determine the resistivity of the given material. We know Resistance R…
Q: Name: Refer to the Resistor Colour Code Chart on the second page to complete the worksheet below.…
A:
Q: R₁=10052 ✓ V=12V C₁ = 10 mF R₂=1001 what is the voltage across the capacitor when the switch is open…
A:
Q: Consider the circuit shown in (Figure 1). Suppose that R = 100 kn. Figure 20 ΚΩ 3 ΚΩ 100 V 80 kn 1…
A:
Q: Solve for ID & Vo G
A: The diode can be replaced with its equivalent voltage drop based on the state of the diode and then…
Q: 8. Find the phase relationships between the following waveforms v₁ = 7 sin(@t-80) i, = 5 sin(at +20)…
A: Introduction An AC sine waveform is a type of electrical waveform that oscillates between positive…
Q: What is the minimum sized PVC Schedule 40 conduit we should use for the above wire run if it is 24…
A: 3/4"
Q: AB + BC + AC
A:
Q: 2.14 The spring-mass accelerometer shown schematically in figure 2.16 has a sensing mass of 0.05 kg…
A:
Q: 7. GIVEN THE SECOND ORDER INPut SYSTEM SHOWN BELOW dzy4) dt² +8 dy(t) वट +16y(t) = 4(t) WHERE ult) =…
A:
Q: Usually why do we use a low pass filter before sampling an analog signal? Explain it with an…
A:
Q: Find V2 in order to make Vo=-7.5V
A:
Q: Determine the reverse voltage and reverse current for the diode in the Figure below for each of the…
A: Given: IR = 1µA. Need to calculate reverse current, reverse voltage, and the voltage across the…
Q: What is the total area for the following Aluminum wire run? Six - 350 KCMIL XHHW Stranded Two -…
A: b) 3.7542 in² To find the total area for the given Aluminum wire run, we need to calculate the…
Q: A discharging RC current has a resistor with R equals 40€ and T= 16s. It is known that one T equals…
A: In a discharging RC circuit, the voltage across the capacitor decreases over time and the current…
Q: 13.37 The two switches in the circuit shown in Fig. P13.37 PSPICE operate simultaneously. There is…
A: In this question we need to find i(t) for the given circuit with the help of Thevenin theorem.
Q: AVL vs. BST. Discuss efficiency operations.
A: We need to discuss AVL vs. BST.
Q: Differences between transistors and integrated circuits
A: The differences between transistor and Ics are as fo
Q: 4. For the following circuit, find: a. The inductance value in Henrys and the capacitance value in…
A:
Q: Apply nodal analysis to find i and the power dissipated in each resistor in the circuit below.…
A:
Q: Attempt Only if you are sure . a 24 V DC voltage source is controlled by a rotational potentiometer.…
A: Given data At θ=0°C, V0°C=24 V At θ=12°C, V12°C=10 V To find out We have to determine the voltage…
Q: QUESTION 5 The differences between a standard PLC and a safety PLC are: A standard PLC has one…
A: We need select correct option for given statement.
Q: A block diagram of a system consisting of a sinusoidal voltage source, an RLC series bandpass…
A:
Q: Q1: Use Superposition theorem to find the voltage VSI 12 V 2k ww -www RL 2k 2k ww 26 Vs: Juv
A:
Q: Determine the total impedance Z of an ac circuit containing a resistor (R = 350 ) connected in…
A: Since both question are not interlinked as per the guidelines of bartleby we supposed to answer…
Q: Autotransformer starting uses a(n) ___ 3 phase autotransformer to provide reduced-voltage starting.…
A: Autotransformer The autotransformer is used to transfer power from one circuit to the another…
Q: - Problem 1 For the circuit shown, the 5V DC source has been connected a long time: a) Find the…
A: In this question we need to find the energy stored in inductor, capacitor and power dissipation in..…
Q: Is 10A M R₁ 202 t=0 Sw + L V₁ 3 511 R₂ 352
A:
Q: 40. Consider the circuit shown below. Find I1, I2, and I3. V₁ = 24 V R2 = 6 Ω 12 R₁ = 80 41 13 R3 =…
A:
Q: 17. (I) Compute the voltage drop along a 21-m length of household no. 14 copper wire (used in 15-A…
A:
Q: Magnetic flux densities for HR steel laminations and CRGO are 1.25 T and 1.75 T respectively then…
A: Given- Magnetic flux densities for HR steel lamination = 1.25 T. Magnetic flux densities for CRGO…
Q: A cube made up of a material with relative permeability of 1,12 is in a uniform magnetic field with…
A: Given data, Relative permeability μr=1.12. Permeability of free space μ0=4π×10-7. Magnetic field…
Q: Is the current at question (b) IRMS or is it already the current?
A: It is given that: VRMS=120 VR=20 Ω
Q: 1. Using graphical approach as shown in lecture videos, determine the convolution between r(t) and…
A:
Q: If in the oscillator block diagram shown in Figure, = 0.1V, A = 100 and m = 0.01, then the circuit…
A: Given oscillator block diagram: V1=0.1 VA=100β=m=0.01
Q: ven the input signal r(t) and system impulse response h(t) as: r(t) = u(t)-u(t-4) h(t) = u(t)e-t…
A: Given Data: An input signal of, xt=ut-ut-4 An impulse response of, ht=12ute-12t To Find: yt…
Q: UL 1st digit 2nd digit Multiplier Tolerance The first band indicates: The second band indicates: The…
A:
Q: The initial voltages on capacitors C1 and C2 in the provided circuit have been established by…
A: In this question We need to determine the energy stored in the capacitors at the t->∞. We know…
Q: Q7 (answer on the lab worksheet): Using the circuit in this experiment as a guide, design a 4-level…
A: Given data The input voltage range is given as, Vin=2V, 4V, 6V, 8V To find out We have to design a…
Q: 1= M 3 00Ka 1.60 г мл M Find V₁ 160 ка ви
A:
Q: Find the Thevenin equivalent with respect to the terminals a,b in the circuit in. Suppose that R =…
A:
Q: The initial voltages on capacitors C1 and C2 in the provided circuit have been established by…
A: In this question We need to determine the energy stored in the capacitors at the t->0. We know…
Q: A narrow band frequency modulated (NBFM) signal is given by s(t) = 2cos (2nfet) + 0.2 sin(2πfmt…
A: Given data st=2cos2πfct+0.2sin2πfmt+0.2πsin2πfct Carrier frequency, fc=140 kHz Message frequency,…
Q: SP6.14 Determine the output Y for a 2-input AND gate with the input waveforms as shown below. Show…
A:
Q: A transformer circuit breaker is equipped with 500/5 A C.T.s connected to a induction type over…
A: Given- A transformer circuit breaker- 500/5A C.T.s 125% plug setting and 0.4 time setting, 3-ϕ fault…
Q: Given the linear mechanical system below: Determine the transfer function ?3(?)/?(?). Express your…
A: In this question We need to determine the transfer function. We are solving this problem using the…
Q: Explain briefly, which type of Analog control can achieve or realize with LOGO? | plc
A: We have to explain which type of Analog control can achieve or realize with LOGO?
Step by step
Solved in 3 steps with 3 images
- You are an electrician working in a plant. A series resonant circuit is to be used to produce a high voltage at a frequency of 400 Hz. The inductor has an inductance of 15 mH and a wire resistance of 2 . How much capacitance should be connected in series with the inductor to produce a resonant circuit? The voltage supplied to the circuit is 240 V at 400 Hz. What is the minimum voltage rating of the capacitor?In the circuit of Figure, the magnitudes of V₁ and V at the resonance are twice L C that of VD. The inductance of the coil for R* 50 Hz is 520⁰ VR www. 502 Vc ell V₁In a series RLC circuit, the applied voltage is 108V. At resonance, the frequency is 200rad/sec, and the circuit current is 8.38 A. What is the resistance of the circuit (in Ohms)?
- What is resonance? Explain how the condition of resonance is obtained in a series RLC circuit. Determine impedance, current, and power factor of RLC circuit at resonance.A parallel R-L-C circuit is fed by a constant current source of variable frequency. The circuit resonates at 100 kHz and the Q-factor measured at this frequency is 5. Find the frequencies at which the amplitude of the voltage across the circuit falls to (a) 70.7% (b) 50% of the resonant frequency amplitude.In a series RLC circuit, the applied voltage is 120V. At resonance, the frequency is 200rad/sec, and the circuit current is 6.26 A. What is the resistance of the circuit (in Ohms)? (Use 2 decimal places. Unit is not required.)
- The current at resonance in a series R-L-C circuit is 0.12mA. The circuit has an induc- tance of 0.05 H and the supply voltage is 24 mV at a frequency of 40 kHz. Determine (a) the circuit resistance and (b) the circuit capacitance.Eill in the blank with corect answers B Frequency Series Resonance - Impedance vs. Frequency. The graph of impedance against frequency for an RLC series resonance circuit is shown in the picture. At which point the current will be maximum At point A At point C At point B At point D The inner most layer of an optical fhotI Is cantu ImpedanceA series circuit consists of a 120V, 50HZ source, a 300 resistor, a 100mH inductance, and a variable capacitance. Find the capacitance required to create a series resonance condition at this frequency. O 202.8uF 507.12uF O 101.4uF O 676.16uF
- The inductance coil in the series resonant circuit is 0.2 H, and the resistance coil is 50 Q. At what capacitance value does resonance occur at 1500 kHz in this circuit? Assuming a 100 V r.m.s. e.m.f. at the source.Calculate the bandwidth in kHz Blank 1 and an inductor's Q Blank 2 at100MHz. It has an inductance of 6mH and a series resistance of 1.2k2.A series circuit consists of a reactor of 0.1 henry inductance and 5 ohms resistance and a capacitor of 25.5 μ F capacitance. Find the resonance frequency and the percentage change in the current for a divergence of 1 percent from the resonance frequency. [100 Hz, 1.96% at 99 Hz; 4.2% at 101 Hz]