Magnetic flux densities for HR steel laminations and CRGO are 1.25 T and 1.75 T respectively then ratio of weight of CRGO laminations and HR laminations (Assuming same densities is for two type of core material and total flux remains the same.)

Magnetic flux densities for HR steel laminations and CRGO are 1.25 T and 1.75 T respectively then ratio of weight of CRGO laminations and HR laminations (Assuming same densities is for two type of core material and total flux remains the same.)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Related questions

Q: 7. Given the voltage waveform below, plot ux (t) + determine the dc value. 13x sr 44 55 V5 201 DIA…

Q: A PV-module has the nominal power, Pp=400W when the irradiance G=1000 W/m2 and Tmodule=25 ºC.…

Q: Which of the following is the greatest barrier to efficient smart homes? A) lack of infrastructure…

A: Which of the following is the greatest barrier to efficient smart homes? A) lack of infrastructure…

Q: 2- How much power is delivered by Vs?

Q: 1. A silicon p-n junction has the hole and electron resistivity are 0.001 2.m, 0.004 22.m…

A: Dear student, Since you have posted multiple questions, we will provide the solution only to the…

Q: Standing between the tall building, you live over Makati City. You use typical household amounts of…

A: We need to explain about PV system .

Q: 11.28 (System Analysis) For each circuit shown in Figure P11.28, assume that R-10, C-1 F, and L-1 H…

Q: A circuit consisting of a coil with inductance 10 mH and resistance 20 Ω is connected in series with…

A: In this question We need to determine the value of capacitance, current through the coil at the…

Q: Vb=5V, R1=4Ω, R2=8Ω, R3=12Ω, R4=16Ω Compute the listed: Equivalent resistance of entire system.…

Q: For the circuit attached below Given: IA = 4 amperes, VB = 18 volts, R1 = 1/2 ohm, R2 = 1/3 ohm, R3…

A: In this question we need to find the value of Vy (in volts)

Q: Given points M(2, 8, -21) and N(28, 21, -12), RMN = _____. (Answer in this format:

A: Given that Points M,N are as given below. M(2, 8, -21) and N(28, 21, -12),

Q: Leni purchases a property in the Mountain Province's hills, a great distance from the city. He…

A: We need to provide the solution for leni's problem

Q: The velocity of the silicon electrons at room temperature for an electric field of 1 kV/cm is…

A: The formal definition of mobility is the value of the drift velocity per unit of electric field…

Q: 11.2 (Laplace Transforms) Find the Laplace transforms of the following: (d) r(t) = (1-e¹)u(t)

A: We need to find out Laplace transform of given signal.

Q: Design a series RLC circuit with B = 20 rad/s and ωo= 1000 rad/s Find the circuit's Q. Let R = 10 Ω

Q: Problem 12.48 In the circuit shown in (Figure 1), the sinusoidal source delivers a current of i =…

Q: Consider the circuit shown in (Figure 1). Suppose that R = 100 kn. Figure 20 ΚΩ 3 kn 100 V 80 kn 1…

Q: 3. Given the following circuit, solve for V₁. Must use Current Divider.

A: It is given that:

Q: 7. In the following circuit 8. Use Mesh Current Analysis to determine the mesh currents Identify the…

Q: Assume a downlink low-rate communication transmit 500 bits/second at carrier frequency of 2 GHz. If…

A: To determine if the reception incurs any distortion, we need to consider the Doppler effect caused…

Q: Figure Vg 75 ΚΩ 120 ΚΩ ●5V 5V

A: answer : given that an inverting op-amp To find the output of the op-amp

Q: R(s) 1/s -5 1/s -2 1/s -3 x1 x2 -10 -20 -30 Y(s)

Q: 9.34 (Central Ordinate Theorems) Use the central ordinate theorem and the Fourier transform X(f) to…

A: Given: xt=rectt-0.5

Q: (a) ideal ammeter (Give your answer in mA.) mA (b) ideal voltmeter (Give your answer in volts.) V…

A: The required parameters can be calculated by using the node voltage and the node voltage can be…

Q: For the circuit shown above, what is the magnitude of the load impedance Z₁ that will result in…

A: The circuit diagram is shown below, Where,R=25 ΩXC=23 Ω

Q: Illustrate the use of an All-pass-filter after an IIR filter. Illustrate it with an appropriate…

A: An all-pass filter is a type of filter that has a flat frequency response, meaning it does not…

Q: 3. Calculate vo 11, 12, 13, 14and the power dissipated across each resistor. Draw the figure again…

Q: Basic of electrical circuits (a) A 5 μH inductor is driven by a current I(t) = 10 sin (2π 10t) mA.…

Q: бv +1 6k 3 О 23 М 12V ЧК + Vo

Q: Bonus Question: Find an equation for the impulse response h[n] of an LTI filter whose frequency…

A: Given the signal ,

Q: Q31 For the circuit below, 1. Calculate i3 and Vx. 2. Find the power delivered to the 6 Ohm…

Q: The current in the figure below is 0.61 A. (Let the internal resistance of battery 1 be r₁ = 1.102…

A: The required parameters can be calculated by using kirchhoff's voltage law and ohms law. Based on…

Q: Q2) Use mesh analysis to find the voltage “Vo” in the circuit shown below. 1 ΚΩ Ix 1ΚΩ + 12V ΤΑ ΑΙ…

A: We need to find out voltage for given circuit by using of mesh analysis.

Q: 13.37 The two switches in the circuit shown in Fig. P13.37 PSPICE operate simultaneously. There is…

A: In this question we need to find i(t) for the given circuit with the help of Thevenin theorem.

Q: Q3) Using any method of circuit analy the circuit shown below. +1 55 W 20 -W 15 S

Q: E1 R1 A R2 E2 Figure 10.1 R3

A: We need to find out the node voltage for given circuit by using of superposition theorm.

Q: QN8 A magnetic circuit shown below has cast iron core whose dimensions are given below: Length (ab +…

Q: The depletion region width on the p- side, xp, was found to be 20% of the entire depletion region…

Q: For the circuit shown above, what is the magnitude of the load impedance Z₁ that will result in…

A: The given circuit diagram is shown below, Consider R=25 Ω,and,XC=23 Ω.

Q: The pathway for a binary electrical signal between gates in an integrated circuit can be modeled as…

A: first find the differential equation governing the circuit then obtain the complementary function…

Q: The primary voltage of a 2300/230 volts transformer has a frequency of 60 cycles. What is the…

A: It is given that: V1V2=2300230 Vf=60 cycles

Q: Using Boolean algebra, simplify the following expressions

A: The given expression is,F=C+CDC+C¯DC+E.

Q: Find the sinusoids represented by the following phasors 15 V-i(4+ 16) V

Q: Consider a downlink communication from base station to mobile user. The carrier frequency is 6 GHz…

A: Given parameters: Carrier frequency: fc = 6 GHz Channel bandwidth: B = 5 MHz Transmit antenna gain:…

Q: A Class II hazardous location is where_ Select one: Oa. gasses are present Ob. combustible dust is…

A: We need to select correct option for given statement.

Q: 5. Given the following circuit, solve for V₁. Must use mesh Analysis. 6 mA 6 ΚΩ 12 mA 3 ΚΩ 12 V Σ12…

Q: A 20 MVA, 11.2 kV, 4-pole, 50 Hz alternator has an inertia constant of 15 MJ/MVA. If the input and…

A: Given- A 20 MVA, 11.2 kV, 4-pole, 50 Hz alternator has, Power rating, S = 20 MVA Inertia constant, H…

Q: 1- If the highest frequency of the modulating signal is 3 kHz, the bandwidth of the DSBAM- SC signal…

A: We need to select correct option for given each problem .

Q: A paralel-plate capactor is constructed using a dielectric material whose dielectric constant is…

A: Introduction The potential difference between two points is the work done to move a charge from one…

Q: A 2-pole d.c. shunt generator gave the following open-circuit characteristics when running at 1000…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Question

Magnetic flux densities for HR steel
laminations and CRGO are 1.25 T and
1.75 T respectively then ratio of weight
of CRGO laminations and HR laminations
(Assuming same densities
is
for two type of core material and total
flux remains the same.)
..

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question A suspension type insulator has three units with self-capacitance C and ground capacitance 0.1C. What will be the string efficiency?
Which of the following is not true for ferromagnetic materials? Please choose one: a. High?mthey have value. b.Above the Curie temperature, they lose their non-linear properties. C. a fixedµrthey have value. D.The energy loss is proportional to the area of the hysteresis loop.
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
a core type transforem is constructed with 0.014-in. thick laminations having a uniform width of 2.75 in. If the maximum flux and flux density are, respectively, 6.2 X 10' maxwells and 8.2 X 10 maxwells per square inch and the air spaces between laminations occupy 8 per cent of the stacked core, calculate the number of laminations in the transformer. I
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
Please answer last part and show all work, thank you.
A triac can pass a portion of …………… half-cycle through the load a. neither positive nor negative b. both positive and negative c. only negative d. only positive
2. A C-core with a gap of 0.0001m has a coil number of 100 and a current of 10mA. First find the reluctance of the core given that the Iron core has a negligible reluctance and only the air reluctance contributes to the majority of reluctance. The core has a cross sectional area of 2cm². Next find the flux flowing thru the C-core.
Q.4/ choose true or false: 1. The reluctance of any core is proportional directly with the length of it and inversely with both the permeability and the cross-section area of it. 2. The number of parallel paths in wave windings is equal to twice of the number of poles. 3. In dc machines with same values of Z, N, Ø, the emf for wave winding type is more than emf of lab winding type. 4. If we insert a current in such a conductor subjected to a constant magnetic field, a movement will achieved giving the principle of electric generator.
Compare dielectric properties of oil with solid Insulators and liquid Insulators. Compare dielectric strength of transformer oil, and solid dielectrics, gas dielectrics.
Which of the following statement is true? a. Angle between load voltage and load current in a pure capacitive load is 45 degree. b. Angle between load voltage and load current in a pure capacitive load is is 180 degree. c. Angle between load voltage and load current in a pure capacitive load is is zero. d. Angle between load voltage and load current in a pure capacitive load is is 90 degree.
2. Why the core losses varying with the load?