An inverting amplifier circuit using Op-Amp 741 IC, a feedback resistor R-145 k and input resistor, RA is used in a feedback oscillator circuit. The output pin of the amplifier is connected to the three RC network that can generate frequency of oscillation of 50 kHz. Assume that R₁ R₂ R3-R and C₁-C₂-C3-C. Name the oscillator circuit. (iii) Analyse and draw the oscillator circuit. Using a capacitor value of 0.001 µF, design the circuit by determine all other component values.

An inverting amplifier circuit using Op-Amp 741 IC, a feedback resistor R-145 k and input resistor, RA is used in a feedback oscillator circuit. The output pin of the amplifier is connected to the three RC network that can generate frequency of oscillation of 50 kHz. Assume that R₁ R₂ R3-R and C₁-C₂-C3-C. Name the oscillator circuit. (iii) Analyse and draw the oscillator circuit. Using a capacitor value of 0.001 µF, design the circuit by determine all other component values.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter11: Thermostats, Pressure Switches, And Other Electric Control Devices

Section: Chapter Questions

Problem 23RQ

See similar textbooks

Similar questions

An Op-amp has a slew rate of 5 V/microsec. The largest sine wave output voltage possible at a frequency of 1 MHz is ?
-4) Design a circait containing a comparater with a hy steresis loop a. Draw the circuit with all values of the components required for the dksign. b. What is the name of the circuit in (a). c. Sketch the output waveform when the input is a 15-V peak sine wave. d. Adjust the value of RI in the circuit such that the hysteresis width will be 10.
A Sine wave is input for the Op-Amp circuit. For output signal, peak to peak voltage is 30Vpp. a) Calculate Rf resistance value. b) Draw the output signal.
Using any number of Op-Amps, design multistage amplifier to amplify input Ac signal with 0.01V amplitude, the expected output voltage would have 4V amplitude. The input signal frequency = 10 KHz. Assume gain bandwidth product of Op-Amp = 1 MHz
7. The output of an-op-amp vottage follower is a triangula wave as shown in Figure for a squate wave Pinput of frequency 2 MHY poak amplitud e. squale and 8V peak What s the slew rate of the VoA to OP-amp? 3V -3V
You are tasked to look for a converter circuit design that has the specifications tabulated in Table I. The aim is to produce an output voltage of 20 V which can be used to drive a load of 120 W. The converter must operate in CCM. Table I: Design Specifications Values 35 V Design Parameters Input voltage Switching frequency Output current ripple Output voltage ripple 60 kHz 5 % 1 % a) Sketch the final converter and label all parameter values
Determine the type of opamp circuit, the gain and the output voltage of the circuit for each of the operational amp circuits below
1- Mention any two advantages of Integrated Circuit . 2- For the circuit given below : Vin is a sine wave Vinpp=6 V and Vref=-2.4 V , Assume Vsat=±12V Name the circuit and draw the input and output waveforms . Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block
write forward paths and feedback paths.
6. Refer to the RC Phase-shift Oscillator below. A Vin R₁ + Rf 6.a. Derive the feedback factor formula for this circuit. 6.b. Draw the output waveform. C C mm C Vout wwwww
A single-phase full converter is supplied from 230 V, 50 Hz source. The load consists of R-100 and a large inductance so as to render the load current constant. For a firing angle delay of 30, determine (a) average output voltage (b) average output current (c) average and rms values of thyristor currents and
Draw the circuit diagram of DC to DC converter using switched capacitor.