An ideal single-phase source, 240 V, 50 Hz, supplies power to a load resisto R= 100 2 via a single ideal diode. |(a) Calculate the average and rms values of the current and the power dissipation. |(b) Calculate the circuit power factor and the ripple factor. (c) What must be the rating of the diode?

An ideal single-phase source, 240 V, 50 Hz, supplies power to a load resisto R= 100 2 via a single ideal diode. |(a) Calculate the average and rms values of the current and the power dissipation. |(b) Calculate the circuit power factor and the ripple factor. (c) What must be the rating of the diode?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
For the circuit shown below, compute the maximum current through each resistor when terminal A is a) positive and, b) negative. Assume the diodes are ideal. (Will we convert to the RMS value to it's actual value?)
In the circuit of figure Nº A, the secondary voltage Vs is 15 volts rms with a frequency of 60 Hz, R equal to 100 Ohms and C equal to 1000 microfarads. The diodes are silicon (Vd = 0.7 volts) and the Zener diode is 15 volts. Determine:a) The magnitude of the ripple voltage at Cb) The Magnitude of the Peak Inverse Voltage (PIV) for D1 and D2..
Consider the following circuit diagram. Using practical diode model solve the following items. i. What is the type of rectification in this circuit? ii. Calculate the total peak secondary voltage (Note that “RMS" value is given in the circuit) iii. Sketch the plot of time vs voltage over Load (RL) iv. Find the average voltage over Load. v. Find the maximum current passing over diodes. vi. Find the peak inverse voltage (PIV) over the diodes. vii. Find the minimum fuse current rating for the primary coil. 5:1 D DA 120 V rms D3 D2 RL=10kQ RL out ell lelll
1) How is the diode and zener diode in the electronic circuit and how they work?indicate the differences between them.2) Can a zener diode be used instead of a regular diode? please explain.3) Is it to step down and rectify the 220V AC signal by means of a transformer or to convert 220 V?rectify it and then reduce its value to the desired DC level using a voltage divider circuit?suitable.?4) Bridge type full wave rectification with two diodes full wave rectification using a medium ended transformerCompare the rectifier circuit and list its advantages and disadvantages relative to each other.5) What is the concept of PIV (Peak Inverse Voltage) for rectifier circuits?For which rectifier circuits is this value more important?
Discussion: 1. Discuss the obtained curves. 2. What are the advantages of using cascade voltage regulator circuit? 3. To stabilize a voltage of 65 V, one can: a. Use one 65V zener diode b. Use ten 6.5 V zener diodes in series If the costs are irrelevant, then which solution is best and why?
One component that does not need to be installed in the correct orientation is a: a. Resistorb. Diodec. Voltage regulatord.
A R-load half-wave rectifier used sinusoidal voltage source with a peak value (35.353kV). The firing angle is (30). The total resistance is 50k2 and frequency is 50HZ. Calculate (in details): load direct voltage, maximum direct voltage, normalized voltage and effective voltage, power delivered to the load, power factor, form factor, ripple factor?
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
The three-phase circuit shown in figure 1 is 220 Vrms per phase and 50Hz. Diodes are real. The circuit produces an output shown in Figure 2. Indicate the conduction angle of diode D5. What times does this conduction correspond to? Use the first cycle only (0-360°). to-0 sec.
EXAMPLE: A single-phase, full-wave center-tapped rectifier supplies power to a 1-k2 load. The ac voltage applied to the diode is 600 V rms. If the diode resistance is 25 N and that of the transformer secondary is negligible. Determine (a) average load current (b) average value of load voltage Note: The rms value of the ac voltage across each secondary half is 300 V.
Which of the following statements about bridge tip rectifiers is false? A) If the 1-phase type has source inductance, the average value of the output voltage is lower than in the absence of the inductance. B) The average output voltage value of the 1-phase type is 0.9 times the peak voltage of the network. C) none D) There are only odd harmonics in the current drawn by the 1-phase type from the mains. E) The average value of the output voltage of the 3-phase type is larger as the 3-phase and 1-phase types are compared