The Figure 2 shows an electronic circuit designed for supplying power to a load (RL). The supply voltage 235V (RMS, AC) at frequency of 50HZ. The required DC voltage and power for the load are 24V and 3.6 W respectively. The Electrical Components of this AC to DC converter are: A full-wave rectifier to convert AC voltage to DC voltage. A regulator with transistor and Zener diode to ensure a constant voltage and power for the load. DI 01 V VLoad D2 D3 VI sine Regulatee Reifier Figure 2. Complete Circuit Assume that the diodes are real diodes (NOT ideal diodes). The following information is available: The collector to base resistor of the regulator R1 = 5.0 k2 The transistor Q1 with ß value of 24 is used for the regulator circuit. Determine the following quantities for this electronic device and fill the table below: | Question Answer The voltage of Zener Diode (Vz) The current in R1 The DC current into the regulator

The Figure 2 shows an electronic circuit designed for supplying power to a load (RL). The supply voltage 235V (RMS, AC) at frequency of 50HZ. The required DC voltage and power for the load are 24V and 3.6 W respectively. The Electrical Components of this AC to DC converter are: A full-wave rectifier to convert AC voltage to DC voltage. A regulator with transistor and Zener diode to ensure a constant voltage and power for the load. DI 01 V VLoad D2 D3 VI sine Regulatee Reifier Figure 2. Complete Circuit Assume that the diodes are real diodes (NOT ideal diodes). The following information is available: The collector to base resistor of the regulator R1 = 5.0 k2 The transistor Q1 with ß value of 24 is used for the regulator circuit. Determine the following quantities for this electronic device and fill the table below: | Question Answer The voltage of Zener Diode (Vz) The current in R1 The DC current into the regulator

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit in the figure, an AC voltmeter will be made with full wave rectifier circuit structure. R = 50ohm and diodesResistance values in the direction of transmission are Rd = 100ohm. Inside of the DC ammeter to be used as indicatorthe resistance is very, very small. The AC mark to be measured is Vs = 100 Sinwt Volts.a- Draw the shape of the current passing through the DC Ammeter and calculate its maximum value.b- Find the average value of the current passing through the DC Ammeter.c- Analyze the voltage seen at the ends of diode D1 for both alternans.d- Find the Rms value of the voltage seen at the ends of the diode D1.
A full-wave rectifier uses 2 diodes. The internal resistance of each diode is 20 Q. The transformer RMS secondary voltage from centre tap to each end of the secondary is 50 V and the load resistance is 980 Q. Mean load current will be
A three phase full wave rectifier is shown below along with peak phase voltage Vm-169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is %3D VDc=280.7V and the output RMS voltage is equal to VRMS=280.93V. The efficiency, FF and RF are respectively equal to: Secondary D D D, R AD. Z D. D, Select one: O a. 99.83%, 100.08%, 4% O b. 99.83%, 55.08%, 4% O C. 99.83%, 100.08%, 16% O d. 87.83%, 100.08%, 4%
A single-phase full-wave bridge rectifier circuit is fed from a 220 V, 50 Hz supply. It consists of four diodes, a load resistance 20 Q and a very large inductance so that the load current is constant. What is the average or dc output voltage?
1.) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor. 2.) A 12 V rms ac supply is connected to the primary winding of a transformer with a turns ratio of 0.052. Calculate the rms secondary voltage given a voltage regulation of 4.0% 3.)Sketch the circuit for an ac supply input to a full-wave diode rectifier with a resistive load and no smoothing capacitor.
3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
1) AC power in a load can be controlled by using a. Two SCR's in parallel opposition b. Two SCR's in series c. Three SCR's in series d. Four SCR's in series 2) The advantage of using free - wheeling diode in half controlled bridge converter is that a. There is always a path for the ac current independent of the ac line b. There is always a path for the dc current independent of the ac line c. There is always a path for the dc current dependent of the ac line d. There is always a path for the ac current dependent of the ac line 3) Silicon controlled rectifier can be turned on a. By applying a gate pulse and turned off only when current becomes zero b. And turned off by applying gate pulse c. By applying a gate pulse and turned off by removing the gate pulse d. By making current non zero and turned off by making current zero
Draw the circuit diagram of a half-wave rectifier for producing a nearly steady dc voltage from an ac source. Draw two different full-wave circuits.
In the given Full Wave Center tapped Rectifier circuit, a step down transformer gives an RMS voltage as 110v/11-0-11 V is used with R1-1 Kn. Assume diode as Germanium. a) Find Input Voltage D, Vin b) Find Peak Output Voltage. c) Find Average Output Voltage. d) Find Current through the load resistor. eelee
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
A half-wave rectifier is to provide an averagevoltage of 50 V at its output.a. Draw a schematic diagram of the circuit.b. Sketch the output voltage waveshape.c. Determine the peak value of the output voltage. d. Sketch the input voltage waveshape.e. What is the rms voltage at the input?
Determine the voltage across the diode, the output voltage, and the current in the resistor in the figure below. Plot these waveforms with proper ac cycle phase alignment. 1SR154-400 is a silicon rectifier 1 ampere diode. Indicate the peak values as per calculation.