Answered: 2. For the truss shown below, determine…

2. For the truss shown below, determine the stress in members AC and BD. The cross-sectional area of each member is 850mm². [94.12, 78.42 MPa]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Pin-connected rigid bars AB, BC, and CD are initially held in the positions shown by taut wires (1) and (2). The bar lengths are a = 36 ft and b = 27 ft. Joint Cis given a horizontal displacement of 5.7 in. to the right. (Note that this displacement causes both joints B and C to move to the right and slightly downward.) What is the change in the average normal strain in wire (1) after the displacement? B (1), a (2) Answer: = i (0)
Pin-connected rigid bars AB, BC, and CD are initially held in the positions shown by taut wires (1) and (2). The bar lengths are a = 24 ft and b = 18 ft. Joint Cis given a horizontal displacement of 8.4 in. to the right. (Note that this displacement causes both joints B and C to move to the right and slightly downward.) What is the change in the average normal strain in wire (1) after the displacement? b В (1), (2) D Answer: E = i
The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A1 = 340 mm2 and a length of L1 = 3.6 m. Rod (2) has an area of A2 = 315 mm2 and a length of L2 = 1.2 m. Assume dimensions of a = 3.4 m, b = 1.2 m, and c = 1.5 m. After a load of P = 60 kN is applied to the rigid bar at D, determine:(a) the normal stresses in rods (1) and (2)(b) the magnitude of the downward deflection of the rigid bar at D.
I need the answer as soon as possible
Asap
For the truss loaded as shown, Determine the axial stress developed in members AB, AD, BC, and BD state what type of stress are developed. Considering that all members have the same cross- sectional area of 900mm^2.
9. Find the stresses in members BC and BE for the truss shown. The cross-sectional area of each member is 3780 mm². Indicate whether the stresses are tensile (T) or compressive (C). BC = 4.44 MPa (C), BE = 3.45 MPa (T) B C 50° 50° 50⁰° E 20 KN 50% D
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
The steel truss with E=200GPais loaded as shown in the figure. Determine the following: the following a) the deformation of member AB if the cross-sectional area is 2500mmb) the deformation of member AD if the cross-sectional area is 1800mm A 4.0m 200 KN B D 4.0m 1² 2.5m
1. For the roof truss shown in Figure 3, determine the force present in ele- ment GH and in each element located to the right of GH. Also, establish whether the elements are in tension or compression. (I suggest you start from node M applying the method of nodes until you get to element GH) -2.4 m--2.4 m-1.2 m-2.4 m--2.4 m--1.2 m- 1.5 kN 1.5 kN 1.5 kN 1.5 kN D VI 1.5 kN 1 kN В 2.5 m E Ук 1 kN 1m H F Figura 3. Cercha 3. 2.Determine the force in the elements ED, EH, and GH of the reinforcement (see Figure 4), and establish whether the elements are in tension or compres- sion. (Use the method of sections). Figura 4. Cercha 4. 50 kN 40 kN -2 m -2 m- -2 m- 1.5 m -30 kN 1.5 m B 40 kN 1.5 m
Experts Pleae help ASAP
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. C D I-KE -1.2 m-1.2 m 1.2 m B