Using a minimum amount of M112, how many packages are required to cut a steel shaft 24" in circumference?

Q: What is the total weight of the following pieces of steel: 6-W8 x 28 that is 12'-6" long 4 W12x40…

A: Given Data  Determine the total weight of the following pieces (W)

Q: When the length of the board is in inches, what is the formula used for B.F? _____

A: Board foot ( B.F.)  is the standard unit used for measurement of lumber

Q: what is the r value for a 2"x12" BOND and r value for 2"x12" WOOD RIM JOIST?

A: In any construction, the R-value estimates a material's ability to oppose heat stream from one side…

Q: What are the advantages of tightening a structure?

A: According to a Civil Engineering structural construction: The major advantages of a tightening a…

Q: steel reinforcing bar is stretched until it breaks

A: To calculate the minimum elongation at which the bar will break for steel bars of varied grades.…

Q: Why do real lumber dimensions vary from nominal measurements? Explain.

A: The variances are due to the fact that lumber sizes are generally presented in nominal sizes. The…

Q: Draw the picture of double acting hammer? Explain how it works ?

A: Many of the piles for the task were driven with impact hammers. An impact hammer is made up of a…

Q: What is the yield strength, ultimate tensile strength, and shear strength of a Carbon Graphite Rod…

A: Carbon graphite Rod grade JC3 -It is a dense fine grain road and is machinable to a higher…

Q: Explain the purpose of each part of the AISI steel designation code?

A: AISI steel designation code:

Q: In the design of watermain, the normal practice is to use ductile iron for pipe size less than 600mm…

A: The Exact Reason for the Same is Illustrated Below:

Q: Calculate Joint Strength of 5.5 inch, 23 lb/ft, N-80 grade casing, and maximum length of casing (in…

A: Given, D = 5.5 in  Ultimate strength (σu) = 80 ksi

Q: What is the efficiency of joint when strength of bolt per pitch length is 60 KN and strength of…

A: Given: Strength of bolt per pitch length = 60 kN. Strength of plate per pitch length = 150 kN

Q: Two plates 4ft  x 8 ft plate ½ inch thick is to be joined lengthwise. A welding machine to be used…

A:

Q: How we can calculate the weight of 12m long and 10mm dia. Steel on-site?

A: The given data is: Length, L=12 m Diameter, D=10 mm

Q: how do you find SSD?  how is SSD 1.47?how do you determine breaking conditions? How is it 2.5?

A: The speed of the vehicle = 40 mph The gradient of the uphill = 5% To determine:- The value of the…

Q: What is a double-acting hammer?

A: A double-acting hammer can be defined as it is a type of hammer that utilizes compressed air or…

Q: What is Pneumatic caissons.

A: Caisson is a watertight retaining structure or chamber that is used for the repair of ships,…

Q: What is double-tube core barrel ? How it is used ?

A: Core Barrels Core barrels are the devices or instruments which are used for drilling in hard,…

Q: Define the Bearing resistance failure, punching failure, squeezing ?

A: Bearing resistance failure A bearing capacity failures are defined as foundation failure that occurs…

Q: Please define how Can reinforcing steel be tack welded as an alternative to using wire ties or…

A: 1. It depends on local standards and codes. Much steel is welded into grid patterns for lightweight…

Q: What is the efficiency of joint when strength of bolt per pitch length is 60 KN and strength of…

A: Strength of bolt per pitch length is 60 kN, Strength of plate per pitch length is 150 kN.

Q: Immerse samples of interior and exterior plywood in water. Continue until delamination occurs. Keep…

A: Interior Plywood: Interior plywood is used as a material for indoor works. Interior plywood should…

Q: what is the nominal maximum load capacity of a grade 60 reinforcing bar with a diameter of 20 mm?

A:

Q: Discuss Selection and Sizing of Anchor Bolts

A: Solution: When anchoring, the general rule is that the embedded depth  should be at least 4 diameter…

Q: Explain the Hollow-stem auger components ?

A: Solution: Hollow stem Auger are the kind of drilling which is like solid stem except the Claw Bit…

Q: what is the Weight of the wood if the cross-section is 200 mm x 200 mm?

A: Data Given: A = 200 mm × 200 mmWood projection when placed in water = 55 mmWood projection when…

Q: What is the types of shrenkage ?

A: Shrinkage is characterized as the contracting of a solidified solid combination because of the…

Q: Explain the functions of different components of a typical expansion joint?

A: An expansion joint is a mid-structure separation that is intended to relieve stress on building…

Q: What are some characteristic features of aluminum extrusions, and what is the function of each?

A:

Q: How to determine that a pipe belongs to flexible or rigid pipes category?

A: Answer Rigid pipeRigid pipes are strong that can withstand live load and dead load easily. A rigid…

Q: Summarize the various types of core barrels and their sizes, ?

A: A core barrel is a device used for the collection of the core of the drilled rock.

Q: what would be the throat area of a fillet weld with equal legs of 6mm and length of 1cm?

A: Leg size of fillet weld = 6mmLength of weld (Lw) = 1cm = 10mmThroat area  =?

Q: Describe the standard split spoon.

A: The apparatus which can be split into two equal half portion along theri length is known as split…