Consider two shafts one solid of mild steel of 200 mm diameter and another hollow of alloy steel of which outer diameter is 200 mm. Ratio of different properties of hollow shaft to solid shaft are tabulated as follows: Properties Ratio of hollow to solid Allowable shear stress (max) Power (P) Rotational speed (N) 1.45 1.40 1.04 The maximum value of internal diameter of hollow shaft is mm. (Round off to two decimal places).

Consider two shafts one solid of mild steel of 200 mm diameter and another hollow of alloy steel of which outer diameter is 200 mm. Ratio of different properties of hollow shaft to solid shaft are tabulated as follows: Properties Ratio of hollow to solid Allowable shear stress (max) Power (P) Rotational speed (N) 1.45 1.40 1.04 The maximum value of internal diameter of hollow shaft is mm. (Round off to two decimal places).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Find: (a) the stress in the Steel and Ahuminium rods after the loap P applied and the temprature raised 60 C" and (b) the displacement under the load P. Using the data in the Table below. Rod A (mm) a (um/m. C) L (m) d (m) 0 (degree) E (GPa) P (kN) Steel 500 T1.2 190 3 35 Aluminium 400 18.9 22 70 Aluminium Steel 4m 2m
_Find: (a) the stress in the Steel and Ahuminium rods after the loap P applied and the temprature raised 60 C" and (b) the displacement under the load P. Using the data in the Table below. Rod A (mm) a (um/m. C°) L (m) d (m) 0 (degree) E (GPa) P (kN) Steel 400 T1.2 195 3 35 Aluminium 300 18.9 4 30 90 Aluminium Steal 4m 2m
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm A = 400mm? A- 200mm 40KN 10KN 20KN 1.5m 2.5m 2.0m Determine the change in length of steel rod having a length of 800mm and a diameter of 6.5mm. The rod is subjected to a force P equal to 110KN. Young's Modulus is 200GPA Compute normal strain of the rod
2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as shown in the figure. Axial loads are applied at the positions indicated. The cross-sectional area of the rod is 300sq.mm. Express your answer in MPa. Determine the stress in the steel. b. a. Determine the stress in the aluminum. Determine the stress in the bronze. C. STEEL ALUMINUM BRONZE 56kN 14kN -0.6m- -0.9m- -0.76m-
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
The dimensions of the compressed air tank manufactured in the form of a cylinder are given in the figure. 6mm thick steelThe tank is manufactured by joining the plate with a helical weld at an angle of 30°. parallel to the weld seamSince the safe shear stress in the direction is 30 MPa, the maximum pressure that can be used in the tank is determined.calculate.
An aluminium channel section is shown in the figure below: mm 1; mm mm li mm As indicated, the horizontal sides are of length / = 167 mm and thickness 1 - 1 mm while the vertical side is of length l2- 218 mm and thickness 12 - 3 mm. Determine the shear stress in the top side when it is subject to a pure torque of 20 Nm. You may assume that the factor ki may be taken as 0.333. Give your answer in N/mm² to three decimal places.
Determine the normal stress in the steel plate. Gusset plate is 16 mm thick column pin diameter = 20 mm gusset plate steel plate 70 kN pin 60mm 8-mm plate thickness 183.45 MP 0148.53 MPa 58.33 MP3 22282 MP A 14583MP
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0, calculate the maximum load in N that the bar can support. А) 12500-pi в) 6250*pi с) 3125*pi D) 1563*pi
PROBLEM 3 A compound shaft consisting of a 50mm diameter bronze segment and a 75mm diameter aluminum segment is subjected to two torques shown. Determine the maximum permissible value of T if the stress of bronze is limited to 60Mpa, the stress in aluminum is limited to 70mpa and the angle of twist of the free end is 10 deg. G for aluminum= 28GPA and G for bronze = 35 GPa. 27 37 Aluminum bronze it 2M 2
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa Aluminum L=2m A=500mm 2m 2m E-72Mра P=20KN