A uniform beam of length 20 m and mass 100 kg is supported by pylons on cither end. A 200-kg box is centered at 14 m from the right end of the beam. WWhat is the downward force on the left most pylon? Your Answer: Answer

A uniform beam of length 20 m and mass 100 kg is supported by pylons on cither end. A 200-kg box is centered at 14 m from the right end of the beam. WWhat is the downward force on the left most pylon? Your Answer: Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(а) In Figure Q3(a), using the method of joints and free-body diagrams, determine the force in each member of the truss. Indicate whether each member of the truss is in tension or compression. 12 kN D В 4 m Figure Q3(a) (b) Determine the centroid C(x, ỹ) of the plane area as shown in Figure Q3(b). 21 24 y Dimensions in cm 6. 36 Figure Q3(b) 6 m 3 m
A sign for a pizza restaurant hangs from a 2.60-m long rod extended out from a building. A cable, attached to the building, is attached to the rod at a point that is 2.10 m from the hidge. (See the figure.) The mass of the rod is 3.20 kg. The mass of the sign is 7.10 kg. The angle between the building and the rod is 69.0 degrees. The angle between the cable and the horizontal is 36.0 degrees. The tension in the cable is 117.5 N. What is the vertical component of the reaction force from then hinge on the rod?
A 2x3m plate with a weight of 900 kg is lifted with the help of three cables connectedto each other ww www at the D point located right abovethe center of the slab. Find the forces in the cables. D 3m O TAD =450 kG, TBD =383 kG, TcD= 326 kG )O TAD =350 kG, TBO =333 kG , Tco= 316 kG TAD #400 kG, TBp =313 kG , TCD= 366 kG 1,5 m-1,5 mtim d) TAD 315 kG, TBD =393 kG, TCo 366 kG
Weight=255 Can you also explain in detail thank you
The lumbar portion of the human spine supports the entire weight of the upper torso and the force load imposed on it. We consider here the disk (shaded red) between the lowest vertebra of the lumbar region (L5) and the uppermost vertebra of the sacrum re- gion. (a) For the case L = 0, determine the com- pressive force C and the shear force S supported by this disk in terms of the body weight W. The weight W. of the upper torso (above the disk in question) is 68% of the total body weight W and acts at Gj. The vertical force F which the rectus muscles of the back 25 mm L3 L4 L5 G2 4r exert on the upper torso acts as shown in the figure. (b) Repeat for the case when the person holds a weight of magnitude L assumptions. W/3 as shown. State any Sacrum %3D 300 mm 50 mm 3王

The gate AB of shape isosceles triangle is hinged at location A. The gate weighs 1000 N. For the equilibrium, what horizontal P force should be applied at B. (poi= 9700 kg/m³) 2,5m Syag= 3700 ka A' 2m 45
Two builders carry a sheet of drywall up a ramp. Assume that W = 1.9 m, L = 3.3 m, theta = 19.0⁰, and that the lead builder carries a weight of 109.0 N (24.5 lb). L- Ө What is the weight carried by the builder at the rear? HINT: Consider the drywall to have no thickness. The builder at the rear gets tired and suggests that the drywall should be held by its narrow side. ~W~ 0 What is the weight he must now carry? HINT: From the previous problem, you know how much each builder carries. Therefore you know the total weight. Set the sum of the torques about the front lower corner to 0, so that you do not need to know the weight carried by the builder in front.
Free body diagram (FBD) 30 3 kN 2m - 2 m 1.5 m 45° 8 kN-m
B: A 30 m long vessel with cross section shown in Fig. 4 is to carry a load of 6000 kN. If the free surface far 0.535 m from the top of the vessel and if the vessel mass is 100000 kg? Determine whether the vessel is stable or unstable? 8 m 1 m Free Surface 0.535 m 2 m Water 2 m 3 m 5 m 5 m Fluid X Water Mercury 0.5 m Fig. 3 Fig. 4
Awnser
4. A pry bar of length 0.6 m is used to slightly lift one side of a 120-kg rectangular cabinet of side L as shown in Figure 7. The center of gravity of the cabinet is a distance L/3 from its rear side. What force P has to be applied to the end of the pry bar and perpendicular to it? L/3 CG L 4 cm 0.6 m 30°
As indicated in the diagram below, a beam is loaded. kN is the equivalent of the reaction R2. 20 kN 40 kN 2 m W= 20 kN/m 2 m 4 m R1 R2