A 2x3m plate with a weight of 900 kg is lifted with the helo of three cables connected to each other at the D point lacatedright above the center of the slab. Find the forces in the cables. D O TAD #450 kG, TBD =383 kG, TCD= 326 kG b) TAD 350 kG, T80 -333 kG, Tco 316 kG 0 TAD #400 kG, TBD -313 kG, TCD= 366 kG 1m 1,5 mt-1,6 m im d) TAD 315 kG, TBO -393 kG, Tco" 366 kG.

A 2x3m plate with a weight of 900 kg is lifted with the helo of three cables connected to each other at the D point lacatedright above the center of the slab. Find the forces in the cables. D O TAD #450 kG, TBD =383 kG, TCD= 326 kG b) TAD 350 kG, T80 -333 kG, Tco 316 kG 0 TAD #400 kG, TBD -313 kG, TCD= 366 kG 1m 1,5 mt-1,6 m im d) TAD 315 kG, TBO -393 kG, Tco" 366 kG.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.39P: The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables...

See similar textbooks

Similar questions

Find the internal force systems acting on sections 1 and 2.
The bent rod of negligible weight is supported by the ball-and-socket joint at B and the cables attached to points A and C. Find the forces in the cables and the magnitude of the reaction at B. Dimensions Figure P.5.39
The structure is supported by a pin at C and a cable attached to A. The cable runs over the small pulley D. Find the internal force systems acting on sections 1 and 2.
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.
2- Find the applied force by the hydraulic cylinder in the truck shown graphically using KS: 1cm=1m, KF: 1cm=1 kN. W=25 kN
Find the tension in each of the supporting cables in the figure when the weight of the crate is 500 newtons.
The wheels, axle, and handles of a wheelbarrow weigh W = 55 N. The load chamber and its contents weigh WL = 623 N. The drawing shows these two forces in two different wheelbarrow designs. To support the wheelbarrow in equilibrium, the man’s hands apply a force to the handles that is directed vertically upward. Consider a rotational axis at the point where the tire contacts the ground, directed perpendicular to the plane of the paper. Find the magnitude of the man’s force for both designs.
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and the cast is W=210 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=6 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=33°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) b) Find the tensile force T2 in cable 2. (Write your result in N) c) Find the angle α of cable 1 with the horizontal.
2. Find the forces acting at pins C and D of the given frame. loworod slowly onto 2.2 m -3 m 2m DI 3 m3 m- B 4 m 240 N
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
The figure shows a mechanical model of the Russel fracture traction device and the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=200 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=10 cm . Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A ( 3L/4= 75 cm) . The angle that cable 2 makes with the horizontal is measured as β=40 ° . Accordingly, in order for the leg to remain in balance in the position shown; a) Find the tensile force T 1 in cable 1 . (Write your result in N ) b) Find the tensile force T 2 in cable 2 . (Write your result in N ) c) Find the angle α of cable 1 with the horizontal
An eye bolt is used to attach 3 cables to a steel plate. The tension in the three cables create F1=200 lbf, F2=250 lbf, and F3=100 Ibf with 0 = 30 degrees and p=44 degrees. If the eye bolt is in equilibrium, what is the y-component of the sum of other forces on the bolt (force from the nut and plate on the bolt) ? If you add up %3D the three force vectors, the sum other force you are looking for will just be in the opposite direction to put the eye bolt in equilibrium. The y-direction is positive going up. For example, if you find the sum of forces 1, 2, and 3 are 100 Ibf going up, then the other forces in the y-direction must be pointing to the down (-100 lbf) to put the eye bolt in equilibrium. Eye bolt steel plate Nut & Washer esc DOO D00 F4 F3 AA %24 F10