A three phase full converter is supplied by a phase voltage Vs-120V, 50 Hz. The rectifier supplies a resistive load R=100 Q. If the RMS value of the output current is equal to 1.375A, then the RMS value of the input line current I, would be equal to: Select one: O a. 1.123A O b. 2.458A O c. 3.995A O d. 5.015A

A three phase full converter is supplied by a phase voltage Vs-120V, 50 Hz. The rectifier supplies a resistive load R=100 Q. If the RMS value of the output current is equal to 1.375A, then the RMS value of the input line current I, would be equal to: Select one: O a. 1.123A O b. 2.458A O c. 3.995A O d. 5.015A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

H.W3 The single-phase full wave controlled rectifier has a R-L load with R= 0.552 and L= 6.5mH. The input voltage V, 220V at 50Hz. The delay angle is a-30, plot the input and output waveforms. Then determine: -The average thyristor current -The rms thyristor current -The output rms current -The average output current - The efficiency NOTE: Drive any formula that used in solution
A full-wave rectifier is connected to a single-phase source and supplying an inductive load. For the sake of simplicity, you can assume that the ripple at the output current is negligible. Input specifications: The source is single-phase utility grid at 220 V and 50 Hz. Output specifications: The load resistance is 10 Ohm. Sketch the schematic of the system. Sketch the waveforms of the output voltage and current and the source voltage and current. Determine all the performance parameters.
A three phase full wave rectifier is shown below along with peak phase voltage Vm-169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is %3D VDc=280.7V and the output RMS voltage is equal to VRMS=280.93V. The efficiency, FF and RF are respectively equal to: Secondary D D D, R AD. Z D. D, Select one: O a. 99.83%, 100.08%, 4% O b. 99.83%, 55.08%, 4% O C. 99.83%, 100.08%, 16% O d. 87.83%, 100.08%, 4%
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
Design a rectifier fed from 220-V line through a step-down transformer. The load requires an average voltage of 9 V and average power of 2.5 W. Use each of the three circuits: half-wave, center-tapped full-wave and bridge type full-wave. pls write legibly and show complete process of solution
A three phase full converter is supplied by a phase voltage V5-120V, 50 Hz. The rectifier supplies a resistive load R=100 Q. Suppose that the average output voltage is 40 % of the maximum possible average output voltage. The delay angle a would be equal to: Select one: O a. 44.42deg O b. 88.42deg O c. 66.42deg O d. 22.42deg TOSHIBA
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V rmsh soHz} VL-DC =20V 0.01 F 0.02 F 0.0167 F None of the above
The input to a full-wave rectifier is 30 V AC (RMS). The load resistor is 10 ohms. The DC power at the output is: O A. 73 W O B. 18 W C. None of the other choices are correct D. 36 W O E. 146 W
Design a rectifier fed from 220-V line through a step-down transformer. The load requires an average voltage of 9 V and average power of 2.5 W. Use each of the three circuits: half-wave, center-tapped full-wave and bridge type full-wave.
C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is 10k D1 R2 LM324 VEE applied to the input signal VIN? Vin D2 10k OUT V3 U1A Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When VIN is positive the circuit conducts but only to one diode drop, B. When VIn is negative the circuit operates as an inverting amplifier providing an inverted sine wave at VouT. When VIN is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When VIn is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VOUT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at Vour. When VIn is positive the…