A steel penstock has a 36-in. outer diameter, a 0.5-in. wall thickness, and connects a reservoir at A with a generating station at B. Knowing that the specific weight of water is 62.4 lb/ft³, determine the maximum normal stress and the maximum shearing stress in the penstock under static conditions. Take h = 600 ft. (Round the final answers to two decimal places.) 'h 36 in. B

A steel penstock has a 36-in. outer diameter, a 0.5-in. wall thickness, and connects a reservoir at A with a generating station at B. Knowing that the specific weight of water is 62.4 lb/ft³, determine the maximum normal stress and the maximum shearing stress in the penstock under static conditions. Take h = 600 ft. (Round the final answers to two decimal places.) 'h 36 in. B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SECTION: 500mm 20 KN I5 KNIM 1000 mm 12 m Ps 800 KN e : 400 mm (ASSUME IS % LOS SES) A. Determine the stress at the bottom in the free end. (MPa) B. Determine the stress at the top in the fixed end. (MPa)
Current Attempt in Progress The solid 1.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 550 lb/ft. Two concentrated loads also act on the rod: P= 1900lb and Q = 800 lb. Assume a = 14 in. and b = 28 in. Determine the normal stress in the rod at the following locations: (a) x= 9 in. (b) х - 27 in. w В C a b Answer: Ox-9in. psi Ox-27in. psi
F1 (kN) 30 mm 80 mm 30 mm 80 mm F2 (kN) 30° 400 mm The system is loaded with F1 (100) and F2 (200) as shown. Determine the principal stresses, principal planes, and maximum shearing stress and show the stresses on an element (a) at point H, (b) at point K.
Question 1 of 5 /20 E View Policies Current Attempt in Progress The solid 1.05-in-diameter rod is subjected to a uniform axial distributed loading along its length of w3- loads also act on the rod: P= 1900 lb and Q =500 lb. Assume a = 21 in. and b = 42 in. Determine the normal stress in the rod at the following locations: = 975 lb/ft. Two concentrated %3D (a) x = 14 in. (b) x = 42 in. C b. a Answer: psi Ox=14in. psi Ox=42in. Attempts: 0 of 1 used Subr Save for Later
5. A steel wire 5 m long hanging vertically supports a weight of 120ON. Determined the required diameter if the stress is limited to 140 MPa and the tatal elongation must na exceed 4mm. Neglect the weight f the wire and assume E= 200 GPa
Required information Two solid cylindrical rods AB and BC are welded together at Band loaded as shown. Given: P=7 kips. A 30 in. -1.25 in. В 12 kips 25 in. 0.75 in. Find the average normal stress at the midsection of rod BC. The average normal stress at the midsection of rod BC is ksi.
aShubber H.W.2: The load P produces an axial strain of -1,800 ue in post (2). Determine the axial strain in rod (1). 1,200 mm- (1) rigid plate 480 mm 1.5 mm D 300 mm 300 mm 600 mm (2) E
(c) A vertical tie fixed rigidly at the top, consists of a steel rod 2.5 m long and 20 mm diameter encased throughout in a brass tube 20 mm internal diameter and 30 mm external diameter. The rod and casing are fixed together at both ends. The compound rod is suddenly loaded in tension by a weight of 10 kN falling through 3 mm before being arrested by the tie. Calculate the maximum stress in steel and brass. Take Es = 200 GPa and Eg = 100 GPa.
1600-lb in. couple is applied to a wooden beam, of rectangular cross cection 1.5 by 3.5 in., in a plane forming an angle of 30° with the vertical Fig 4.60). Determine (a) the maximum stress in the beam, (b) the angle that the neutral surface forms with the horizontal plane. 1600 lb in. 30 D E 1600 lb- in. 3.5 in. M. 0 = 30° 1.75 in. A 0.75 in.! 1.5 in. Fig. 4.60 Fig. 4.61 B.
14-67. The thin-walled pipe has an inner diameter of 12 mm and a thickness of 0.6 mm. If it is subjected to an internal pressure of 35 MPa and the axial tension and tonsional loadings shown, determine the principal stress at a point on the surface of the pipe. 1000 N+ 1000 N 30 N-m 30 N-m
1.7 m 20-mm-diam. pin double sh 14-mm-diam. rod 4.2 m (1) single s 24-mm-diam. pin 5.2 m The structure supports a distributed load of "w". The limiting stress in rod (1) is 380 MPa, and the limiting stress in each pin is 200 MPa. If the minimum factor of safety for the structure is 2.10, determine the maximum distributed load magnitude w that may be applied to the structure plus the stresses in the rod and pins at the maximum w.
a) Transform the beam into one made entirely of steel. b) The steel channel is used to reinforce the wood beam. Determine the maximum stress in thesteel and determine the maximum stress in the wood if the beam is subjected to a moment of M=1.2kN.m Est = 200GPa, Ew12GPa. (please give explanations and step by step solutions if possible)