A simply supported beam is loaded as shown in the figure below. Use superposition theory to find: a) the reaction at the supports b) the deflection at point A {Hint: Take E = 30,000 kpsi and I = 0.2485 in'} \ft= %3D

A simply supported beam is loaded as shown in the figure below. Use superposition theory to find: a) the reaction at the supports b) the deflection at point A {Hint: Take E = 30,000 kpsi and I = 0.2485 in'} \ft= %3D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.5.9P: The cantilever beam AB shown in the figure has an extension BCD attached to its free end. A force P...

See similar textbooks

Related questions

Q: En fem (5) meter lang bjelke er opplagret i A, B og C, som angitt på skissen. Bjelken har et kN ledd…

A: Given:The outer downward directed evenly distributed load, The concentrated horizontal load,

Q: Question 2 A fixed-fixed beam in Figure Q2 1s loaded by a triangularly dıstributed load of maxımum…

A: Draw the free body diagram of the beam as shown in figure.

Q: Question 2 A beam ABC of length 3m has one support at the left end and the other support at a…

Q: A beam of uniform rectangular section 200 mm wide and 300 mm deep is simply supported at its ends.…

A: The objective of the question is to find the slope at the supports and the maximum deflection of a…

Q: A simply supported beam ABCD is subjected to a linearly distributed load, with wo = 100 N/m, two…

Q: A cantilever beam shown below has a rectangular cross-section, 3/8 in. wide by 1 in. high. The…

A: Beam Details:Rectangular cross-sectionWidth (b) = 3/8 in.Height (h) = 1 in.Length (L) = 20…

Q: b) A cantiliver beam ABC shown in Figure Q3(b) has a span length of L m carry a point load P at…

Q: SHOW THE FOLLOWING: 1. COMPUTATION OF REACTIONS 2. SHEAR AND MOMENT DIAGRAM 3. MAXIMUM BENDING…

Q: Q.A solid structure of rectangular cross-section is simply supported, as shown in Figure Q. The…

A: Given: The elastic modulus, E = 200 GPa The dimension of cross-section of beam, x = 100 mm = 0.1 m

Q: Figure Q1 shows a cantilever beam ABCDE subjected to a uniformly distributed load, w from points B…

A: The loading diagram is Here, the UDL is extended upto point E and a upward counterbalance UDL from…

Q: ire Q3. AB is 2 m, BC is 2 m and CD is 1 m in lengths. By using Macaulay's hod, calculate the:…

Q: Select the correct Shear and Bending Moment Diagrams for the loading and supports shown. Note:…

Q: 3P2: A simply supported beam of constant El and length L IS supporting a distributed load omega w…

Q: The bending stiffness of the beam given in the figure is constant and EI is given. a) Draw the…

A: A moment is a movement of the body when a body is rotating on an axis. The moment is also known as…

Q: The figure shows a cantilever consisting of steel angles size 100 x 100 x 12 mm mounted back to…

A: given data; ⇒w=1KN/mF=2.5KN⇒OA=2m⇒OB=3m⇒AB=1m

Q: Figure Q2 (a) shows a simply supported beam ABCD under two point loadings at B and C, respectively.…

A: To find: The value of P that causes the total depth of the plastic zone to be 10 mm at the most…

Q: As shown in Figure Q3, a beam ABC is fixed at A and roller supported at C. The beam is used to…

Q: A built-in cantilever beam with a hollow rectangular cross-section is subjected to a uniformly…

A: Boundary conditions will use in beam problem to find the integration constant while finding…

Q: 3. An I beam column with fixed ends (at x = 0 and x = 12 m) is braced at midpoint C as shown below…

Q: Calculate the reaction force at support B Calculate the reaction force at support B when the support…

A: Given: A propped cantilever beam as shown in Fig w= 7kN/m P= 14kN flexural rigidity (EI)= 4 MN.m2…

Q: A solid structure of rectangular cross-section is simply supported, as shown in Figure Q2. The…

A: Given: The elastic modulus, E = 200 GPa The dimension of cross-section of beam, x = 100 mm = 0.1 m

Q: 1. A steel beam with an overhang has an inverted T cross section and is subject to loads as shown in…

A: The answer is given in the below attachment

Q: 1. Find the deflection y(x) where:The beam is embedded at x = L and a free end at x = 0. The applied…

Q: For the beam shown below, given that L = 10 m, and w= 14 kN/m, E = 200 x 10 3 MPa, W410 x 100.…

A: To find: The maximum deflection at the center of the simply supported beam with uniformly…

Q: Compute the values of slope and deflection for the beam shown below at x =L by the double…

Q: 20KN 2m 2m Example: (3B): Find the value of the force P to reduce the deflection of point c to the…

A: The forces acting are: 1) A force of 20KN at the end of the cantilever 2) A uniformly distributed…

Q: El

A: To given thatw=7.5kN/m =7.5N/mmL=12×103mmE=10GPa =10×103MPaI=4×10-5m4 =4×10-5×1012mm4K=800KN/m…

Q: Problem 3 For the beam shown in the figure, a) Derive the equation of the elastic curve. b) Compute…

A: Given Data: Moment =2.7 kN.m Uniformly distributed load =300 Nm and it is distributed on 6m length.

Q: Question Four A beam of the cross section that is shown in Figure a was supported by two rigid…

A: given data: maximum allowable tensile stress σ=50MPa own weight of beam(w)=1.5KN/mweight of beam…

Q: Pin-joint construction supports point loads as shown below: P L C 1/3 L Al ΕΙ B 2/3 L a) Find the…

A: (a) To find: The equation for the deflection of the bar at point B. Given: The force acts at point C…

Q: 1. In figure (1), shows a uniform beam subjected to a linear increasing distributed load. The…

Q: QUESTION 3 Given the beam shown in Figure Q3, calculate the reaction at point A, consider El to be…

A: Only one question is allowed to solve.

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

100%

L15 in-dia. shaft
A simply supported beam is loaded as shown in the figure below. Use superposition
theory to find:
a) the reaction at the supports
b) the deflection at point A
{Hint: Take E= 30,000 kpsi and I = 0.2485 in'} \ft=
%3D
15 in
24 in
340 lbf
150 lbf/ft
B
A
1.5 in-dia. shaft

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Beam ABC is loaded by a uniform load q and point load P at joint C. Using the method of superposition, calculate the deflection at joint C. Assume that L = 4 m, a =2ra, q = 15 kN/m, P = 7.5 kN, £ = 200 GPa, and / = 70.8 X 106 mm4.
A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable deflect ion at point C is 0.5 mm, select the lightest W360 section from Table F-l{b) that can be used for the beam. Assume that L = 3 m and ignore the distributed weight of the beam.
Beam ACB hangs from two springs, as shown in the figure. The springs have stiffnesses Jt(and k2^ and the beam has flexural rigidity EI. What is the downward displacement of point C, which is at the midpoint of the beam, when the moment MQis applied? Data for the structure are M0 = 7.5 kip-ft, L = 6 ft, EI = 520 kip-ft2, kx= 17 kip/ft, and As = 11 kip/ft. Repeat part (a), but remove Af0 and instead apply uniform load q over the entire beam.
A cantilever beam has a length L = 12 ft and a rectangular cross section (b = 16 in., h = 24 in.), A linearly varying distributed load with peak intensity q0acts on the beam, (a) Find peak intensity q0if the deflection at joint B is known to be 0.18 in. Assume that modulus E = 30,000 ksi. (b) Find the location and magnitude of the maximum rotation of the beam.
Copper beam AB has circular cross section with a radius of 0.25 in. and length L = 3 ft. The beam is subjected to a uniformly distributed load w = 3.5 lb/ft. Calculate the required load P at joint B so that the total deflection at joint B is zero. Assume that£ = 16,000 ksi.
-3 The deflection curve for a simple beam AB (see figure) is given by v=q0x360LEI(7L410L2x2+3x4) Describe the load acting on the beam.
Compound beam ABC is loaded by point load P = 1.5 kips at distance 2aB from point A and a triangularly distributed load on segment BC with peak intensity qü= 0.5 kips/ft. If length a = 5 ft and length/) = 10 ft, find the deflection at B and rotation at A. Assume that £ = 29,000 ksi and / = 53.8 in4.
Obtain a formula for the ratio c/maxof the deflection at the midpoint to the maximum deflection for a simple beam supporting a concentrated load P (see figure). From the formula, plot a graph of c/max versus the ratio a/L that defines the position of the load (0.5 < a/L < ) What conclusion do you draw from the graph? (Use the formulas of Example 9-3.)
-5 Calen1ate the deflections S 3a nd
The deflection curve for a cantilever beam AB (sec figure) is given by v=q0x2120LEI(10L210L2x+5Lx2x3) Describe the load acting on the beam.
A cantilever beam model is often used to represent micro-clectrical-mechanical systems (MEMS) (sec figure}. The cantilever beam is made of polysilicon (E = 150 GPa) and is subjected to an electrostatic moment M applied at the end of the cantilever beam. 1 f dimensions arc h — 2 [im, h — 4 ^m, and L = 520 ^mt find expressions for the tip deflection and rotation of the cantilever beam in terms of moment M.
A propped cantilever steel beam is constructed from a W12 × 35 section. The beam is loaded by its self-weight with intensity q. The length of the beam is 1L5 ft. Let E = 30,000 ksi. Calculate the reactions at joints A and B. Find the location of zero moment within span AB. Calculate the maximum deflection of the beam and the rotation at joint B.