A Sandwich block is comprised of brass in the centre with two aluminium plates attached to either side. The block is fastened by a top rigid end plate. An axial load (P = 443 KN) is applied to the centre of the block as shown below. Find the normal stress in the brass and the normal stress in the aluminium cover plates. Aluminum plates (E = 70 GPa) 300 mm Brass core (E = 105 GPa) 10 mm 40 mm 10 mm P Rigid end plate 60 mm OneDrive Screenshot saved The screenshot was added to your

A Sandwich block is comprised of brass in the centre with two aluminium plates attached to either side. The block is fastened by a top rigid end plate. An axial load (P = 443 KN) is applied to the centre of the block as shown below. Find the normal stress in the brass and the normal stress in the aluminium cover plates. Aluminum plates (E = 70 GPa) 300 mm Brass core (E = 105 GPa) 10 mm 40 mm 10 mm P Rigid end plate 60 mm OneDrive Screenshot saved The screenshot was added to your

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 1 An axial force of P is applied to the center of the rigid end plate shown below. If the portion of the load carried by the aluminum plates is half the portion of the load carried by the brass core, (a) determine the value of h, (b) the total load if the stress in the brass is 50 MPa. Brass core (E = 105 GPa) Aluminum plates (E = 70 GPa) Rigid end plate 300 mm 60 mim 40 mm
NEED IN 1 HOUR PLS, THANK U A copper bar is of uniform cross-section and is rigidly attached to the walls as shown. The rod is 5ft long and has a cross-sectional area of 2.5 in². At a temperature of 20°F the rod is stress-free in the configuration shown. Determine the stress in the rod when the temperature has dropped to 50°F. Assume that the supports do not yield. For copper, E = 16x10⁶ lb/in² and α = 9.3 x 10^-6/°F.
A hollow aluminum tube is rigidly attached between steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in aluminum of 80 MPa, in steel of 150 MPa or bronze of 100 MPa. Steel Aluminum Bronze А P> ЗР - 2P outside = 30 mm d inside = 20 mm d d = 16 mm d = 60 mm -100mm- -150mm- -125mm-
The length of the assembly shown below decreases by 0.5 mm when an axial force is applied by means of rigid end plates. Determine (a) the magnitude of the applied force, (b) the corresponding stress in the brass core.
Maxinnun allowable stress for steel - 140 MPa Maxinnum allowable stress for ahuminum = 90 MPa Maxinnun allowable stress for brouze - 100 MPa Required: Maximun safe value of axial load P Aluminum A 400 mm Bronze A= 200 mm Steel A= 500 mm 2P 4P 2.5 m 2.0 m 1.5m
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
a)Calculate the stress in the copper bar (in MPa).b)Calculate the axial deformation in the brass bar (in mm).c)Calculate the axial deformation in the brass bar (in mm).
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. Aluminum 3P Bronze Steel 2P P 4P - 1.0 m- - 0.6 m→- ste-0.8 m - A (mm²) E (GPa) . (MPa) Bronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140
The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises after a load W = 120 kN is applied. Steel rod Bronze rod A (mm²) 350 1500 a (/°C) 11.7 x 10-6 18.9 x 10-6 E (GPa) 200 83 O Steel 1.5 m 1.0 m- 2.5 m 9. Determine the stress at the steel rod in MPa when there is a temperature rise of AT = 36 °C. W Bronze 3 m 1.5 m-
r Two Example (2) 8- A compound bar is constructed from three.. wide by 12mm thick together to form a bar somm wide 30 The middle bar is of aluminum alloy for which F-70 GP= outside of brass with E-100 MPa. If the bars are initia at 18c and the temperature of the whole assembly is to to So C, determine the stresses set up in the brass and the Kg = 18 510 Solutions2 FB = FAL FB So*12*10 63 Ext. + Comp. = (XAI - XB) L.A.T. FB.L FAL.L AAL.EAL Ag Eg = DAL + From these equation & FAL=3984 N FB 1992. N 1992 50*121610-6 FB AB -6 XA => 22 *10°-=-=- = (XAL-XB) LAT FAL *100*109 So*12*10% 70 4109 FAL 3984 AAL SO#1210-6 SB = SAL How find that?! = 32. MPa (Ton) FAL. L AP EA = (22-18) x 10² (50-18) XIF_P=15 KN (camp.) Find O'B and GAL F₁+ 2FB = 15 6.64 MPa: (comp)... L FB.L AB. E.B ww.as 17 Brass AL Brass
The 200-mm square aluminum block supports a compressive load of 300 kN. What is the normal stress acting on section a–a in MPa What is the shearing stress acting on section a–a in MPa The lapbelt assembly is to be subjected to a force of 800 N. What is the required thickness t in mm. of the belt if the allowable tensile stress for the material is 10 MPa?