The beam is loaded as shown in Figure AN-02. Assume El to be constant. A. 5 m 13 kN 3 m = B FIGURE AN-02 4 kN/m 5 m C 1. Which of the following most nearly gives the fixed end moment at B due to the concentrated load, FEMBA= [Select] 2. Which of the following most nearly gives the distribution factor at B for member [Select] AB in percent, DEBA 3. Which of the following most nearly gives the moment at B in KN-m, Mb = [Select]

The beam is loaded as shown in Figure AN-02. Assume El to be constant. A. 5 m 13 kN 3 m = B FIGURE AN-02 4 kN/m 5 m C 1. Which of the following most nearly gives the fixed end moment at B due to the concentrated load, FEMBA= [Select] 2. Which of the following most nearly gives the distribution factor at B for member [Select] AB in percent, DEBA 3. Which of the following most nearly gives the moment at B in KN-m, Mb = [Select]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 14200 ksi] rods, and a solid steel [E = 31400 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.68 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.54 in. Assume L1=44 in and L2=81 in. If all bars are unstressed before the load Pis applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 25 kips is applied. (2) (1) L2 (1) L1 A B Answers: i ksi. 02 = ksi.
05 A steel shaft ABC of 50 mm diameter as shown in figure is driven at A by a motor that transmits 50 kW to the shaft at 10 Hz. The gears at B and C remove 30 kW and 20 kW respectively. Compute the maximum shear stress in the shaft and the angle of twist between the ends A and C. (Take G= 80 GPa) Motor A 1.0 m-1.2 m 50 mm B C
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 13700 ksi] rods, and a solid steel [E = 32600 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.84 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.5 in. Assume L1=37 in and L2=66 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 27 kips is applied. (2) (1) L2 (1) L1 A P
Use X = 137 Y = 37 A = 6 B = 8 C = 1
9
Use Use x = 137 y = 37 a = 6 b = 8 c = 1 answer number 20 and 21 only
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 14800 ksi] rods, and a solid steel [E = 32200 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.68 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.54 in. Assume L1=50 in and L2=81 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 21 kips is applied. (2) (1) L2 (1) |L1 B P.
Use x = 137 y = 37 a = 6 b = 8 c = 1
Find the maximum moment of the given load train at point n on the beam given in the figure?
For the beam shown, the magnitude of the distributed load is wo = 10.6 kN/m and the beam lengths are a = 6.3 m and b = 18.9 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Wo В a
Subject structuur