Problem 1 An axial force of P is applied to the center of the rigid end plate shown below. If the portion of the load carried by the aluminum plates is half the portion of the load carried by the brass core, (a) determine the value of h, (b) the total load if the stress in the brass is 50 MPa. Brass core (E- 105 GPa) Aluminum plates (E= 70 GPa) Rigid end plate 00 mm 60 mim 40 mm

Problem 1 An axial force of P is applied to the center of the rigid end plate shown below. If the portion of the load carried by the aluminum plates is half the portion of the load carried by the brass core, (a) determine the value of h, (b) the total load if the stress in the brass is 50 MPa. Brass core (E- 105 GPa) Aluminum plates (E= 70 GPa) Rigid end plate 00 mm 60 mim 40 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.2.1P

See similar textbooks

Similar questions

Maxinnun allowable stress for steel - 140 MPa Maxinnum allowable stress for ahuminum = 90 MPa Maxinnun allowable stress for brouze - 100 MPa Required: Maximun safe value of axial load P Aluminum A 400 mm Bronze A= 200 mm Steel A= 500 mm 2P 4P 2.5 m 2.0 m 1.5m
The assembly consists of two A992 steel bolts AB and EF and an 6061-T6 aluminum rod CD. When the temperature is 30°C, the gap between the rod and rigid member AE is 0.1 mm. Assume BF is also rigid. (Figure 1) Figure 400 mm A B 25 mm 50 mm D 0.1 mm 300 mm E 1 of 1 25 mm Part A Determine the normal stress developed in the bolts if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. of = Submit Part B σ₁ = Submit O HA Value Request Answer Provide Feedback ■μÅ Value Determine the normal stress developed in the rod if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units Request Answer wwwww Units ? wwwww Review ? Next >
A 2014-T6 aluminum tube having a cross-sectional area of 600 mm² is used as a sleeve for an A-36 steel bolt having a cross-sectional area of 400 mm², When the temperature is T=15 °C, the nut holds the assembly in a snug position such that the axial force in the bolt is negligible. If the temperature increases to T-80 °C and an axial force of 25 KN is applied to the assembly, determine the stresses in the bolt and the sleeve. Note: Length of the assembly is 150 mm, E is 200 Gpa, a is 12*106 (for bolt), E is 73.1 Gpa, a is 23*106 (for sleeve).
Assume the transformed steel section reaches its allowable bending stress first. Calculate the magnitude of the allowable bending moment that can be applied in this case. Answer: M- i Ib-in.
A brass sleeve S is fitted over a steel bolt B, and the nut is tightened until it is just snug. The bolt has a diameter of dB = 25 mm, and the sleeve has inside and outside diameters of d1 = 26 mm and d2 = 36 mm, respectively. d2 di dB Sleeve (S) Bolt (B) Calculate the temperature rise AT that is required to produce a compressive stress of 23 MPa in the sleeve. (Use material properties as follows: for the sleeve, as = 21 x 10-6/C and Es = 200 GPa; for the bolt, aB = 10 × 10¬6/°C and EB = 400 GPa.) AT = °C (Round to the nearest whole number.)
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?
4 A flanged bolt coupling has ten 12-mm di ameter steel bolts on 500 mm diameter b olt circle and six 16 mm diameter aluminu m bolts on 300 mm diameter bolt circle. T he maximum shear stresses of the materi als are 60 MPa in steel and 40 MPa in al uminum. Use G = 80 GPa for steel and 3 0 GPa for aluminum. What is the maximu m required shear strength of each alumin um bolt to determine the maximum torqu e that can be applied to the system? Dra wing not included in this problem.
2- The Tensile stress of AISI 1035 Cold-drawn steel is; (a) 550 MPa. (b) 500 MPa. (c) 450 MPa.
An A36 steel plate with width of 400 mm and thickness of 12 mm is to beconnected to a plate of the same width and thickness by 34 mm diametersbolts, as shown in the figure (next slide). The holes are 2 mm larger thanthe bolt diameter. The yield strength of the steel plate is Fy = 248 MPa.Assume allowable tensile stress on net area is 0.60Fy. It is required todetermine the value of b such that the net width along bolts 1-2-3-4 isequal to the net width along bolts 1-2-4.a. Calculate the value of b in mm.b. Calculate the value of the net area for tension in plates in mm².c. Calculate the value of P so that the allowable tensile stress on net areawill not be exceeded.(Use at least 2 decimal points on your answers.)
1.12 A fillet-welded joint of 6 mm size is shown in the figure. The welded surfaces meet at 60-90 degree and permissible stress in the fillet weld is 108 MPa. The safe load that can be transmitted by the joint is 100 mm F F 810 50mm
*7-88. Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while the glass stays approximately rigid. Determine the average shear strain in the nylon due to the load P when the assembly deforms as indicated. 2 mm 3 mm 5 mm 3 mm 5 mm 3 mm
The light rigid bar ABCD shown Is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. E200 CPa E1m 2.0 m 0.6m 1.5 m VP-20 KN Aluminum E-70 GPa A=900mm2 L-1.5 m What is the axial stress at steel rod in MPa?