A pump delivering water at a temperature of 400 F (204.4 C) and a rate of 12,000 GPM (757 lit/s) to a pressurized vessel at 1000 psia. The discharge piping is 135 ft (41.15 m) long schedule 40 stainless steel, and nominal pipe size of 20 in  (7.874 cm). Find the total dynamic discharge head

Q: Water is flowing through a pipe of 5 cm diameter under a pressure of 29.43 N/cm² (gauge) and with…

A:

Q: Suppose a 4-in diameter penstock delivers 140 gal/min of water through an elevation change of 100…

A: Given Data:Diameter of penstock (D) = 4 inchesFlow rate (Q) = 140 gallons/min Elevation change (H) =…

Q: The suction diameter of 60 mm reads 2 psi vaccum and 50 mm diameter discharge with 250 kpag. The…

A: Answer: The horse-power needed to pump the water is 8.15 hp.

Q: Q5: For the system shown in figure. Find the total head loss from (A) to (B). the pipe…

A:

Q: Q2/A Kaplan turbine develops 1500 kw under ahead of 6 m. the turbine is set 2.5 m race while the…

A: Given data as per questionPower develop by Kalpan turbine, P=1500 kWHead, H=6 mDraft tube has…

Q: 2. A 30 cm pipe is connected by a reducer to a 10 cm pipe. Points 1 and 2 a same elevation. The gage…

A: Givend1=30cmd2=10cmZ1=Z2 P1=207 kPaQ12=30 L/s=0.030 m3/shL=2.5m

Q: A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation…

A:

Q: Head, m Consider the plot below, what is the operating flow rate of the pump in this ?system 25 20…

A: To determine the operating flow rate of the given pump.

Q: the (1) two subscripts and (2) sign of the stress components (\sigma, \tau) under the given…

A: we have to define the state of stress for the given coordinate system

Q: The characteristics for a pump are given in the table below. The pump is required to left water…

A:

Q: In the system shown, the water discharge flow rate of 0.0025 m³/s is delivered through the 8 cm…

A: Given data: ◆ The length and diameter of the pipe: L = 406 m , d = 8 cm = 0.08 m ◆ The average…

Q: 34. A pressurized tank contains saturated water. A frictionless valve on the pipe is now opened to…

A: Given Data:Note:

Q: 2. Water at 50°F is pumped from pond 1 to pond 2. Calculate the volumetric flow rate and pump power…

A:

Q: i just need final answer The water is delivered with piping system given in the figure below. The…

A:

Q: 72. A pipe is connected vertically to the discharge side of a pump. The top of the pipe is a short…

A:

Q: Water at 20°C is to be pumped from Reservoir 1 to Reservoir 2 at a rate of 3 m³/min through a 2000 m…

A:

Q: Problem : Taking into account only the local resistances, determine the level difference in the tank…

A:

Q: What power can be delivered by the turbine if its efficiency is 100%? The water flow rate is 0.01…

A:

Q: 3 whot is the pressure in a 9.7-in bore horizontal pipe, :f the bore of the pipe norrows to 4.1 in…

A: Fluid Pressure Fluid Pressure is the pressure at point in the fluid arising due to weight of fluid.…

Q: What is the performance of pump (in %, whole number) that supplies 80 gpm of water (80°F) with…

A: Solution is attached below:

Q: Water at 20°C is being pumped from tank 1 to tank 2 with given conditions. Calculate the power of…

A: Temperature of water, T=20oC Volume flow rate, Q=10 L/s=10*10-3 m3/s=0.01 m3/s Level of tank 1,…

Q: Q2 .. h, are 12m. The pump efficiency is 79%, and the pump is driven by an electric motor. A pump…

A:

Q: A pipe of 180mm bore is delivering water at a rate of 8250dm3/min at a pressure 800kN/m2. It…

A: The volume flow rate remains constant for incompressible flow in a pipe flow. This is due to the…

Q: 152.4 mm, Schedule 40 pipe line 91.4 m long conveys 3028 l/min of cold water from a pump to a point…

A: The frictional head loss in a pipe due to fluid flow can be calculated using the formula given below…

Q: EL..20m K=0.5 A= fi= 0.02 D₁-0.3m Lis 150m F₂2 0.02 Da= 0.6m L₂=240m Valve For Valve K= 0.2 EL.: 5m…

A:

Q: calculate the discharge.

A: Since you ave asked multiple questions, we will solve the first question for you. If you want any…

Q: a) The pressure head supplied by the pump, b) The total head loss between point b and 2.

A:

Q: r=20mm, the friction factor , the shear stress at pipe wall and the head loss per meter of the pipe…

A: Given: s=0.85 ρ=850 kg/m3ν=1.8×10-5 m2/sD=100 mmQ=0.50 L/sTo determine:Center line velocityvelocity…

Q: ump has the following characteristic: Volume flow rate (m³/h) Head (m) 23 46 69 92 115 17 16 13.5…

A: A curve is plotted using the above data sets. Since we have two reservoirs and there is a difference…

Q: FIND THE TOTAL DYNAMIC HEAD IN METER OF THE PUMPING SYSTEM DRAW THE SCHEMATIC DIAGRAM OF THE PUMPING…

A:

Q: Air @ 68°C is pumped through a pipe of internal d = 6.4in: If the vol flowrate is set to 6.2…

A:

Q: 5. A circular pipe of uniform diameter 25.0cm carries water under pressure of 30 N/cm². The mean…

A:

Q: Ex5:- From Figure shown, the pipe line have QA = 15L/s, QB = 3Qp, Da=100 mm, D3= Dc = 25mm, Dp= 50…

A: Given data: The velocity in pipe C is vC = 4 m/s. Consider the velocity in pipes A,B,D are vA, vB,…

Q: Water at 40 °C is pumped from an open tank through 200 m of 50-mm-diameter smooth horizontal pipe as…

A: The pressure encountered by a fluid on the suction side of a centrifugal pump is measured by NPSH,…

Q: Q5: For the system shown in figure. Find the total head loss from (A) to (B). the pipe…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.