A piece of Cu originally 305 mm long is pulled in tension with a stress of 276 MPa. If the deformation is entirely elastic in nature, what will be the resultant elongation? Modulus of elasticity of Cu is 110x10 MPa.

A piece of Cu originally 305 mm long is pulled in tension with a stress of 276 MPa. If the deformation is entirely elastic in nature, what will be the resultant elongation? Modulus of elasticity of Cu is 110x10 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: . An open cylindrical tank 1.2 meters in diameter and 2.1 meters high is 2/3 full of water. After ro...

Q: A binary vapour cycle operates on mercury and steam. Standard mercury vapour at 4.5 bar is supplied ...

Q: A steel shaft 7 ft long that has a diameter of 5 inches is subjected to a torque of 47 kip ft. Deter...

Q: he oil depth is 1.5 m, determine the value of a at A and B during the acceleration.

A: given that initial case initial volume = 4+2+2×2×1-2×12×2×2×1 =...

Q: Explain any one type of ball bearing with a neat diagram and write their applications?

Q: 2. The 1-m diameter cylinder in the figure is 8 meters long (dimension perpendicular to the paper) a...

A: Static Equilibrium Static harmony alludes to any framework where the amount of the powers, and force...

Q: Explain about any two types of belt drives with a neat diagram.

A: GIVEN DATA- BELT DRIVE TOPIC GIVEN WE HAVE TO EXPLAIN ANY TWO TYPE OF IT

Q: The motion of a particle is governed by the relation a = 4t2 , where a is in m/s2 and t in secs. Whe...

Q: PROBLEMS 1 - A ( 200 N ) weight of the block shown in fig. is supported by a pin and bracket at ( A ...

A: GIVEN DATA- A BLOCK SUPPORTED BY PIN AND CABLE WE HAVE TO FIND REACTION AND TENSION

Q: termine the maximum diameter of a ball floating on water at 20°C if it has a density of 6926 kg/m3. ...

A: Given:Density of ball, ρb=6926 kg/m3Density of water at 20o C, ρ=998 kg/m3

Q: A wheel tractor has a 200 HP engine. Calculate the available rimpull of this tractor if it is operat...

Q: 9 kN A 3 m B 63.43 Determine the force in each member of the truss shown. State whether each member ...

Q: 4-130. The building slab is subjected to four parallel column loadings. Determine the equivalent res...

Q: El

A: To given thatw=7.5kN/m =7.5N/mmL=12×103mmE=10GPa =10×103MPaI=4×10-5m4 =4×10-5×1012mm4K=800KN/m =80...

Q: A sheet of steel is stretched biaxially in the xy-plane. The strains in the sheet are described belo...

Q: A 3 inches diameter steel shaft rotates at 215 rpm. if the shearing stress is limited to 14 ksi, det...

Q: The attached answer was provided for the attached question. The equation uses the given temperature ...

A: given; The attached answer was provided for the attached question. The equation uses the given tempe...

Q: . In the set-up shown, a rectangular gate, ABCD, is used to store layers of oil and water. The weigh...

A: Solution: (e) The weight of the block is calculated as: W=1.26×1000 kg/m3×9.81 m/s2×0.5 m×π4×1.2 m2=...

Q: A jet of water of diameter 75 mm moving with a velocity of 25 m/s strikes a fixed plate in such a wa...

Q: 3. The open trapezoidal tank shown in the figure is initially filled with oil (SG = 0.80) up to a de...

A: Specific gravity is an idea that we as a whole have seen yet don't have a clue about its name. Likew...

Q: For an ideal gas, a constant pressure line and a constant volume line intersect at a point, in the t...

Q: 1. The cantilever beam in Figure 1 is fixed at A, and is loaded with a distributed load from A to B ...

Q: owing comp ollow shaft C ed torque of

Q: A wheel tractor has a 200HP engine.if it is operating at an altitute of 1000m above sea level, at an...

Q: the value of Joule-Thomson

A: Given; For an ideal gas, the value of Joule- Thomson co-efficient is: So, For ideal gas, PV=RT T=∂V∂...

Q: Determine the resultant moment produced by forces FB and F pout point O. Express the result as a Car...

Q: The pressure in an automobile tire depends on the temperature of the air in the tire. When the air t...

Q: 2. For the truss shown, calculate the stresses in ksi in members CE, DE, and DF. The cross-sectional...

Q: 700 N 450 N 300 N 30° 60° B algo 1500 N•m 3 m -2 m- -4 m

Q: Consider the two forces Fi en F2 acting on the post in Hibbeler (edition 14) Problem 2.134 P 3.1 Det...

A: F1=400sin35 +cos60j^+sin35sin20j^+cos35k^F1=21.5942i^-78.4699j^+327.6608k^F2=400cos45i^+cos60j^+cos1...

Q: 1. Loads are applied on a pipe made up of steel, bronze and aluminum. The forces and areas are shown...

A: As per stated problem given data is, Load applied on pipe ‘P’=3000lb Area of pipe throughout ‘A’= 0...

Q: The allowable shear stress is Tallow = 805 psi. The supports at A and B are smooth. B 3 ft 6 ft -3 f...

A: Find the maximum allowable distributed load Given data Maximum shear stress = 805 psi

Q: B. If the force vector shown below has x, y, and z components of 300 N, 400N, and 800N respectively,...

Q: Was the mechanical computer first used in a practical application?

A: A mechanical computer is a type of computer that was put together by the use of various mechanical c...

Q: 2 m long aluminium rod must not stretch more than 1 mm and the normal stress must not exceed 38 MPa ...

A: Givenlength of the rod L=2m=2000mmstrech limit ∆La=1mmnormal allowable stress σa=38MPa=38 N/mm2axial...

Q: Given the crystal plane, give the miller index

A: Direction of black arrow in Miller indices Tail side: a1 = 0 a2 = 0 a3 = 0 c = 1 Head Side: a1 = 1...

Q: 4-82. Express the moment of the couple acting on the pipe assembly in Cartesian vector form. What is...

Q: A pot contains water and is heated on a cooker. The cooker adds 23.3 kJ to the pot with 0.8 kJ lost ...

Q: Q.4/ Determine the magnitude of distributed force 5 KN/m and its location on the beam as shown. * Sk...

A: Given that, AB is a beam having UDL of 5kN/m for span of 6 m from A

Q: If block A is intended to move vertically at a constant rate of 4.16m/s, determine the rate (m/s) at...

A: Given: Velocity of block A, VA=4.16 m/s

Q: Determine stress Force=2 Kn Area= 3 m2

A: sol given data :- Force=2 kN Area= 3 m2 stress =?

Q: SITUATION 1: A T-beam is simply supported and is used to carry a uniform load of 20 kN/m. The beam i...

A: Shear stress force tends to cause deformation of a material by slippage along a plane or planes para...

Q: The probability that a randomly chosen shock absorber,

A: Given; An automobile plant contracted to buy shock absorbers from two suppliers X and Y.X supplies=...

Q: The number of units to be produced by the firm such that the profit

A: Given; Cost function for a product in a firm is given by= 5sqWhere, q= ampount of productionThe fi...

Q: Calculate the number of degree of freedom of the mechanism as shown in Fig. P. 1.15.15. 7 3 8 9

A: Answer: The number of degree of freedom of the given mechanism is 4.

Q: Two elevators in adjacent shafts approach each other, one from the top, and the other from the bott...

Q: 5. Determine the resultant internal loadings on the cross section through point D. Assume the reacti...

Q: a) A Diesel engine is working with an injection pressure of 2500 bar and it is cap mode. Briefly exp...

A: given; (a) Diesel engine working (b) difference between PFI and GDI

Q: 1) Determine the average braking torque to be applied to stop the vehicle of mass 1.5 ton is moving ...

Q: 7. At the beginning of compression in an ideal air standard Diesel cycle, the compression ratio is 1...

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

A piece of Cu originally 305 mm long is pulled in tension with a stress of 276 MPa. If the
deformation is entirely elastic in nature, what will be the resultant elongation? Modulus of
elasticity of Cu is 110×10' MPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The original length of a piece of metal is 400 mm, this piece has pulled in tension with stress of 370 MPa. If the elastic modulus is 120 GPa what is the resultant elongation
You are given a square rod of 6061-T6 aluminum (cross-section = 4mm X 4mm, length = 2.3m). The material has a Young’s modulus of 72 GPa. If a compressive load of 3 kN is applied parallel to the 2.3m dimension, what is the resulting engineering normal strain?
2. Consider a cylindrical nickel wire 0.08 in. in diameter and 1200 in. long. Calculate its elongation when a load of 300 N is applied. Assume that the deformation is totally elastic. 3. A cylindrical specimen of a metal alloy 10 mm in diameter is stressed elastically in tension. A force of 3370 Ibr produces a reduction in specimen diameter of 7 x 10* mm. Compute Poisson's ratio for this material if its elastic modulus is 100 GPa. 4. A cylindrical specimen of a hypothetical metal alloy is stressed in compression. If its original and final diameters are 20.000 and 20.025 mm, respectively, and its final length is 74.96 mm, compute its original length if the deformation is totally elastic. The elastic and shear moduli for this alloy are 105 GPa and 39.7 GPa, respectively.
The Highest load sustained druing an uniaxial tensile testing experiment is 7,500lb. If the original cross section has a diamter of 0.25in, what is the ultimate tensile strength? (please also make a drawing)
3. If the engineering strain in a tensile bar is 0.0025 and Poisson's ratio is 0.33, find the original length and the original diameter if the length anddiameter under load are 2.333 ft. and 1.005 in. respectively.
A tensile stress is to be applied along the axis of a cylindrical brass rod with diameter of 200 mm. What is the load magnitude required to produce 2.8 x 10^-2 change in diameter if the deformation is entirely elastic?
1.7C1 1.4C1 ci 0.9C1 Uniform plastic elongation Necking Elastie 0 4 % 15% 35% Strain in % Stress-Strain diagram Stress in MPa
If an isotropic material has a Young's modulus of 120 Gpa and a Poisson's ratio of 0.3, calculate its shear modulus. Select one: O G= 25 Gpa O G= 46 Gpa O G = 77 Gpa O G= 39 Gpa O G= 29 Gpa
A solid cylindrical rod 12 mm in diameter and 50 mm in length is attached to a rigid support at one end and twisted at its free end by 14°. If the Poisson’s ratio for this isotropic material is 0.34 and Young’s modulus is 70 GPa, what is the maximum shear stress induced?
A plastic bar of 88 mm is to be twisted by torques T until the angle of rotation between the ends of the bars is 80. If the allowable shear strain in the plastic is 0.014 radian, what is the minimum permissible length of the bar in mm?
A bar is 500 mm long and is stretched to 505 mm with a force of 50 kN. The bar is 10 mm diameter. Determine stress, strain and elastic modulus.
A plastic bar of 53 mm is to be twisted by torques T until the angle of rotation between the ends of the bars is 9 degree. If the allowable shear strain in the plastic is 0.018 radian, what is the minimum permissible length of the bar in mm?