A milling operation was used to remove a portion of a solid bar of square cross section. Forces of magnitude P = 18 kN are applied at the centers of the ends of the bar. Knowing that a = 30 mm and all = 135 MPa, determine the smallest allowable depth d of the milled portion of the bar. P' a The smallest allowable depth d of the milled portion of the bar is mm.

A milling operation was used to remove a portion of a solid bar of square cross section. Forces of magnitude P = 18 kN are applied at the centers of the ends of the bar. Knowing that a = 30 mm and all = 135 MPa, determine the smallest allowable depth d of the milled portion of the bar. P' a The smallest allowable depth d of the milled portion of the bar is mm.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.4P: A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the...

See similar textbooks

Similar questions

a)Calculate the 5N force, the Vicker Hardness measurement with one corner of the pyramid trace 5mm and the other 8mm. b)Calculate the force of 5N, the Brinell hardness measurement with a ball diameter of 5mm and a trace diameter of 8mm on the part.
A hollow, circular, cast-iron pipe (E, = 12,000 ksi) supports a brass rod (E, = 14,000 ksi) and weight W = 1.5 kips, as shown. The outside diameter of the pipe is d, = 6 in. (Assume the weight density of brass is 520 Ib/ft3.) %3D Nut and washer. (d, = in.) 3 %3D 4 Steel cap (t, = 1 in.) Cast iron pipe (d. = 6 in., t.) L,= 3.5 ft L. =4 ft Brass rod (4,= in.) W h (a) If the allowable compressive stress in the pipe is 15,000 psi and the allowable shortening of the pipe is 0.06 in., what is the minimum required wall thickness t. min (in inches)? (Include the weights of the rod and steel cap in your calculations.) 0.005 X in. (b) What is the elongation of the brass rod 8, (in inches) due to both load W and its own weight? (Use the deformation sign convention.) 0.0229 in. (c) What is the minimum required clearance h (in inches)? 0.0829 in.
Portions of a 0.25 × 0.25-in. square bar have been bent to form the two machine components shown. Knowing that the allowable stress is 9 ksi, determine the maximum load that can be applied to each component. (a) P₁ 1.1 in. P¹ (b)
4. A piercing punch of a die assembly has a diameter of 20mm and will be used to punch in an aluminum plate with a thickness of 4mm. Knowing that the ultimate shear stress of the plate is 280 MPa, determine the force P required to punch through the plate. Punch Aluminum = 4 mm d=20 mm
Use analytical method L1 = 3m L2 = 9m L3 = 3m
The wooden beam shown is made by gluing together planks as shown. 8 kN/m Glue 80 mm A B 80 mm - NA 6 m 80 mm 160 mm Determine the maximum shear stress in the glue in kPa. (2 decimals)
The two wooden boards shown in Figure are connected by a 0.5-in.-diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D = 2 in. and d = 5/8 in. The nut is tightened to cause a tensile stress of 9,000 psi in the bolt. Determine the bearing stress between the washer and the wood. Please explain the solution
!! Show Complete & Detailed Solution w/ FBD !!The figure shows that when the rigid bar is in the horizontal position, the wires are unyielding. The bar rotates clockwise about the pin B through an angle of 2.1° when a force is applied at the handle. Determine the average normal strain developed in wires.a. AHb. CGc. DF
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
A full forming P= 52 kN axial force acts on the part shaped by the machining method made of xCy steel material. The thickness of the part is t= 20 mm and the steel tensile strength is sigma(tensile) = 620 MPa . Calculate the individual fatigue life of the A and B sections of the machine part for 90% reliability. Draw logarithmic S_N diagrams.
1. Two A36 16mm thick steel plates are connected by four rivets shown. 1:11 Pu a. Calculate design strength in KN considering tension failure on gross section yielding. b. Calculate design strength in KN considering tension failure on net section fracture. c. Calculate design strength in KN considering block shear rupture. f. Calculate the ultimate safe load "P" in KN. Given: 500 X =175mm Rivet Dia.=20mm Y=200mm Fy=248Mpa Fu=40 Mpa Bolt Dia.=22mm
7.A cast-iron machine part is acted upon by the 3kN.m couple shown. Knowing that E=165GPA and neglecting the effect of fillets. i) Determine the maximum tensile and compressive stress in the casting ii) Determine the radius of curvature of the casting. 90 mm 20 mm 40 mm 30 mm M = 3 kN m