Scission can be defined as. a. The loss of fragments from the surfaces of ceramic materials due to internal or residual stress b. An increase in the volume of a polymeric materials caused by the absorption of glass or liquid. c. The formation of crystalline regions in amorphous network ceramics. d. The fracture of long chain molecules in polymers subjected to neutron irradiation or radiation by ultraviolet light

Scission can be defined as. a. The loss of fragments from the surfaces of ceramic materials due to internal or residual stress b. An increase in the volume of a polymeric materials caused by the absorption of glass or liquid. c. The formation of crystalline regions in amorphous network ceramics. d. The fracture of long chain molecules in polymers subjected to neutron irradiation or radiation by ultraviolet light

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.8P

See similar textbooks

Similar questions

Which of the following statements are true of dislocations? Select one or more: O a. Dislocations can move under stress O b. Dislocations can arise due to shear deformation of the lattice O C. Dislocations can be viewed with high powered microscopy and not with the naked eye Od. Dislocations primarily enable high stiffness in metals
In an engineering application, the material is a strip of iron with a fixed crystallographic structure subject to a tensile load during operation. The part failed (yielded) during operation and needs to be replaced with a component with better properties. You are told that two other iron strips had failed at yield stresses of 110 and 120 MPa, with grain sizes of 30 microns and 25 microns respectively. The current strip has a grain size of 20 microns. The diameter of the rod is 1 mm and the load applied is 100 N. What is the yield stress of the new part C and would you recommend it for operation? Select one: Oa. 133.5 MPa, yes O b. OC. Od Oe. 120.5 MPa, no 129.5, yes 140.5, no 123.5 MPa, yes
A gold-alloy microbeam attached to a silicon wafer behaves like a cantilever beam subjected to a uniform load (see figure). The beam has a length L = 24.5 um and rectangular cross section of a width b = 4.0 pm and thickness t = 0.88 um. The total load on the beam is 14.9 µN. If the deflection at the end of the beam is 1.53 um, what is the modulus of elasticity E, of the gold alloy (in GPa)? (Use the formulas of this example. The beam has constant flexural rigidity EI.) GPa
Explain why the experimental strength of materials are lower than their theoretical strengths. BI4 Pagr
A structural component in a fighter jet aircraft has a cellular cross-section (Fig. Q1). The component is 2 m long and is fabricated from an Al alloy, whose modulus of rigidity is 30 GPa. During a certain maneuver of the aircraft, a torque of 40 Nm is applied to the component. Using the Membrane Analogy Method, calculate: (a) the torsional shear stress in each cell of the cross-section; and (b) the angle of twist of the component, giving your answer in degrees. 2mm 75 15m 600mm FIG. Q1
At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; a = 12.3 × 106/°F] bar with a width of 3 in. and a thickness of 0.75 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; a = 8.9 x 10-6/°F] bar with a width of 2 in. and a thickness of 0.75 in. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. (1) 3 in. 32 in. O 80.1°F O 118.6°F O 150.7°F O 132.9°F O 110.9°F B 2 in. 44 in. 0.04-in. gap
19 This theory explains that the elastic failure occurs when energy per unit volume in a strained material reaches the value of the strain energy per unit volume at the elastic limit point in the simple tension test. Also, the maximum energy which a body can store without deforming plastically is constant for that material irrespective of the manner of loading. What do you call this theory Bulk Modulus Volumetric strain Hook's Law Elastic Theory Strain energy theory
Two triangular wedges are glued together as shown in the figure. The stress acting normal to the interface, o, is MPa. 100 MPa 100 MPa on 45% 100 MPa -100 MPa
3.What is a dislocation? List five more microscopic defects in bulk materials. Which of the following properties are most sensitive to dislocation structures in materials? a. Young's modulus b. Yield strength c. Conductivity d. Transparency
At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [E = 10,000 ksi; v = 0.32; a = 12.7 x 10-6/°F] bar with a width of 3 in. and a thickness of 0.75 in. Bar (2) is a stainless steel [E = 28,000 ksi; v = 0.12; a = 8.6 x 10-6/°F] bar with a width of 2 in. and a thickness of 0.75 in. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. (1) 3 in. 32 in. 90.2°F O 69.9°F 139.2°F 103.5°F O 111.0°F B ↑ 2 in. ↓ 44 in. -0.04-in. gap
Typically, the perm rating of a material with the material thickness increase O decreases does not change