A metal rod with 10 mm diameter is subjected to 9 kN tensile load. Calculatethe resulting diameter of the rod after loading. Assume that the modulusof elasticity is 70 GPa, Poisson’s ratio is 0.33, and the yield strength is 145 MPa.

A metal rod with 10 mm diameter is subjected to 9 kN tensile load. Calculatethe resulting diameter of the rod after loading. Assume that the modulusof elasticity is 70 GPa, Poisson’s ratio is 0.33, and the yield strength is 145 MPa.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.4P: A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the...

See similar textbooks

Related questions

Q: Two gage marks are placed exactly 250 mm apart on a 12-mm diameter aluminum rod. Knowing that, with…

Q: A RIGID PLATFORM THAT RESTS ON TWO STEEL BARS SHOWN HAS A NEGLIGIBLE MASS Given: A=1500 mm? AAL=3550…

Q: A 20-mm-wide block is firmly bonded to rigid plates at its top and bottom. When the force P is…

A: Given data-

Q: During laboratory testing of an 8-inch steel-alloy rod with a cross sectional area of 32in a tensile…

A: To find modulus of elasticity and Poisson's ratio

Q: A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress…

A: This question is related to the Strength of material. In this question we calculate axial stress and…

Q: A circular aluminum tube of length L = 400 mm is loaded in compression by axial forces P at the…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length…

A: The given data is: Tensile Load on metallic bar (P) = 190 kN Diameter of bar (d) = 16 mm Length of…

Q: A steel rod of original length 200 mm and final length of 200.2 mm after application of an axial…

A: given- original length L=200 mmFinal length Lf=200.2 mmLoad P=20 KN

Q: a. A round steel bar with an initial diameter of 20 mm and length of 2 m is placed in tension,…

Q: } 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm². If a…

Q: A steel bar of length 30 m and having specific weight of 20 x 10-5 N/mm³. Find the elongation of the…

Q: 10/10 FIND STRESS IN Aluminum. IF E st= .200000 MPa, Ealu.=70000 MPa 100 kN

A: The deformation in both the steel and aluminum will be same, to get the stress in the aluminum we…

Q: 1. Determine the nominal load P that will cause failure of the beam shown below. As part of your…

Q: A 1.0 m B 2 kN/m 2 m 5 kN 1.0 m FIG. P5.18 b 200 mm

Q: A metal rod with 0.5 inch diameter is subjected to 2000 lb tensile load. Calculate the resulting…

Q: Problem 7.1. The aluminum bar (cross section 3 cm x 3 cm) shown the figure below is loaded to its…

A: Procedure: To find the elongation of the bar first we need to find the linear strainε. Then…

Q: The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in…

A: Given -

Q: Impact value is used to measure? А. Hardness В. Toughness C. Wheel load D. Strength

A: To find out the impact value is used to measure.

Q: The cantilever beam shown in the figure below carries a downward load that varies from 300 to 700…

Q: If the modulus of elasticity for a given material is twice its modulus of rigidity, then bulk…

A: Given data : Modulus of elasticity=E Modulus of rigidity=C E=2C

Q: Problem # A tensile load of 220 KN is applied to a round metal bar with a diameter of 16 mm and a…

A: Data given: Tensile load = 220 kN = 220 × 103 N Diameter of the bar ϕ= 16 mm gauge length L = 50 mm…

Q: Determine the minimum diameter d of the rod to safely support the load. The rod is made of a…

A: Calculate the maximum moment of beam and shear force Calculate the moment of inertia of a circle and…

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the…

Q: Problem 3: Diameter of the metal bar, before and after load application was measured to be 100.00 mm…

Q: A cylindrical rod with a length of 380 mm and a diameter of 10 mm is to be subjected to a tensile…

A: Solution; The material must be having a yield strength greater than σ=FA=24500 Nπ10*10-3m2=312 MPa…

Q: A cylindrical metal bar with a diameter of 12.83 mm is applied to a load of 17.8 kN. This load…

Q: A cylindrical rod 500 m (20.0 in) long, having a diameter of 12.7 mm (0.50 in.), is to be subjected…

Q: A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and…

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the…

Q: A metal specimen with 20 mm diameter and 100 mm gauge length is loaded elastically with 5 kN and…

A: The bulk modulus is the elastic properties of the object when the object is under pressure the…

Q: A steel rod of original length 200 mm and final length of 200.2 mm after application of an axi…

Q: (b) (i) A tensile test specimen made from 0.4% C steel has a circular cross section of diameter d mm…

Q: If a steel column with cross-sectional area A = 1000 mm^2 modulus of elasticity E = 200 MPa and…

Q: A copper rod with a diameter of 19 mm, modulus of 110 GPa, and a Poisson’sratio of 0.35 is subjected…

A: Given: The diameter of copper d, is 19 mm. Poisson’s ratio is 0.35. The reduction is diameter is…

Q: A 5ft long rod with a 0.63 inch diameter is subjected to a 10,661lb tensile load. What is the…

A: Given data, Length of rod = 5 ft Diameter of rod = 0.63 inch Tensile load = 10661 lb To find out…

Q: A cylindrical specimen of stainless steel having an initial diameter of 12.8?? and initial length of…

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: Two gage marks are placed exactly 250 mm apart on a 12-mm diameter aluminum rod. Knowing that, with…

Q: tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of…

Q: A specimen of ductile cast iron having a rectangular cross section of dimensions 4.8 mm x 15.9 mm is…

A: Modulus of elasticity can be defined as the ratio of the stress experienced by a body or in a body…

Q: A cylindrical rod 500 mm long, having a diameter of 12.7 mm, is subjected to a tensile load of…

A: Finding out different materials criteria.

Q: A drill rod with a diameter of 1/2 in. is made of high-strength steel alloy with a shear modulus of…

A: Given data:

Q: Three rods, each of area 250 mm2, jointly support a 7.5 kN load, as shown in Figure below. Find the…

Q: Question: Determine the diameter of the elastic core of the rod ? Options: A. 13.72 mm B.10.34 mm…

A: Given, Length (L) = 1.5 m Diameter (d) = 20 mm

Q: A 3003-H14 aluminum alloy rod with 15 mm diameter is subjected to a 9-kNtensile load. Calculate the…

A: Given data: D=15 mm T=9 KN C=9 KN E=70 GPa poisson's ratio=0.33

Q: A wood beam is strengthened using two steel plates as shown in the figure below. 1 6 mm A 150 mm 6…

Q: Problem- A round bar made of same material consists of 3 parts each of 100 mm length having…

A: Find the total elongation of bar?

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length…

A: For the given metal bar,

Question

A metal rod with 10 mm diameter is subjected to 9 kN tensile load. Calculate
the resulting diameter of the rod after loading. Assume that the modulus
of elasticity is 70 GPa, Poisson’s ratio is 0.33, and the yield strength is 145 MPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2 at an engineering strain of 6.0. Assume that the deformation is all elastic.
A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
An aluminum alloy cylinder with a diameter of 76 mm and a height of 150 mm. is subjected to a compressive load of 220 kN. Assume that the mate-rial is within the elastic region and a modulus of elasticity of 75 GPa. a. What will be the lateral strain if Poisson’s ratio is 0.33?b. What will be the diameter after load application?c. What will be the height after load application?
A tensile test is carried out on a steel rod of 14mm radius and gauge length of 140 mm. The yield strength ofthe steel (fy) is 500 MPa. At the tension load of 50KN, calculate stress and strain in the steel rod, taking Young’smodulus (E) as 200,000 MPa. Find out if the steel rod is in elastic region or has already yielded. Compute also forthe shear modulus of Elasticity.
A metal rod with 10mm diameter is subjected to 9kN tensile load. Calculate the resulting diameter of the rod after loading. Assume that the modulus of elasticity is70 GPa, Poisson’s ratio is 0.33, and the yield strength is145MPa.
A test piece is cut from a brass bar and subjected to a tensile test. With a load of 6.4 kN the test piece, ofdiameter 11.28 mm, extends by 0.04 mm over a gauge length of 50 mm. Determine:(i) the stress, (ii) the strain, (iii) the modulus of elasticity.(b) A spacer is turned from the same bar. The spacer has a diameter of 28 mm and a length of 250 mm, bothmeasurements being made at 20~ The temperature of the spacer is then increased to 100~ the natural expansionbeing entirely prevented. Taking the coefficient of linear expansion to be 18 x 10-6/~ determine:(i) the stress in the spacer, (ii) the compressive load on the spacer.rC.G.] [64 MN/m 2, 0.0008, 80 GN/m 2, 115.2 MN/m 2, 71 kN.] Could you please answer the parts after the first three? If you use * could you please explain what you mean by it! Thank You :)
A metal rod with 0.5 inch diameter is subjected to 2000 lb tensile load. Calculate the resulting diameter of the rod after loading. Assume that the modulus of elasticity is 10,000,000 psi, Poisson’s ratio is 0.33 and the yield strength is 21,000 psi.
In a standard tensile test, an aluminum rod of 20-mm diameter is subjected to a tension force of P- 30 kN. Knowing that E- 70 GPa, and the change in diameter of the rod- 0.00955 mm, determine the poissons' ratio v. 20n diateter gage length-150 0.33 O 0.6 0.29 O 0.35
Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. USE NSCP 2015.