Solution. A steel rod of original length 200 mm and finallength of 200.2 mm after application of an axialtensile load of 20 kN, what will be the straindeveloped in the rod?

Answered: Image /qna-images/answer/96d96c22-1973-4545-99e4-1e1692f7d4bd.jpg

Answered: A steel rod of original length 200 mm…

A steel rod of original length 200 mm and final length of 200.2 mm after application of an axi tensile load of 20 kN, what will be the strain developed in the rod?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2DP

See similar textbooks

Related questions

Q: 6.0 KN 1.0 m-1.0 m -4.0 m 2.0 kN/m 2.0 m B 000

Q: sample weighing 11.23 lb. and Gs= 2.65, compute the tion

Q: Draw a neat sketch of a Trickling Filter unit and discuss how it can remove impurity from…

A: Context: Trickling filter

Q: This is the corresponding tensile stress (MPa) at the minimum strain (as allowed by NSCP2015) of…

Q: 3/42 For what value(s) of the angle will the acceleration. of the 80-lb block be 26 ft/sec² to the…

Q: am given in the figure, he equation of elastic curve by integration method. (T), (M.) diagrams of…

Q: The 2-lb collar is released from rest at A and slides freely up the inclined rod, striking the stop…

A: For the given arrangement,

Q: Given average angle, radius of curvature and minimum curvature methods. MD, 100 feet MD₂= 200 feet…

Q: Find the: Righting moment Overturning moment Factor of Safety against sliding Factor of Safety…

Q: 1) the total flow from reservoir A in Fig. 1 is 0.3940cu m/sec and the discharge from pipes 4 is…

Q: A. lem 5m 4m Determine the max positive and negative shear and max positive and negative moment at…

Q: Problem Find the midspan deflection 8 for the beam shown in Fig., carrying two triangularly…

Q: stimate the primary consolidation settlement; when the bottom san with a 5 m thickness of a clay…

A: Given:- qnet=1.2MN/m2 size=1.7x2.2m To find:- elastic settlement

Q: A tie-down on the deck of a sailboat consists of a bent bar bolted at both ends, as shown in the…

A: Step-1

Q: A horizontal beam 16 ft long is subjected to a load of 500 lb located to its center. The dimension…

A: Given: Beam with point load at center Beam dimensions To find: Flexural stress Notations; M =…

Q: The spring of constant k is unstretched when the slider of mass m passes position B. If the slider…

Q: At a section in the triangular channel the average velocity is 8 ft/s. Determine (a) the critical…

Q: Water flows over a concrete spillway into a rectangular channel 9 m wide through a hydraulic jump.…

A: The answer is found to be Discharge= 93.70 m^3/s For explanation please refer the attached solution,…

Q: B. Write shear and moment equations for the beams in the following problems. In each problem, let x…

A: In this three beam are given and we are to find bending moment equation

Q: compound curve is at 15 +480, 1₁-30, 1₂-36, D₁-4°, D=5" t is the sta. of the vertex of the compound…

Q: 8. A section of two-lane, two-way rural road has a 4km length of sustained 5% grade with following…

Q: Find the total water pressure in kN on a vertical circular gate 2 m in diameter with its top 3.5…

A: given that Diameter of the circular gate = 2m

Q: The minimum eccentricity to be considered for an axially loaded RCC column of size 400 mm x 400 mm…

A: given Axially loaded RCC columnsize 400 mm×400 mmunsupported length 5 m= L=5000 mm

Q: .Righting Moment • Overturning Moment . . Factor of Safety Against Sliding . Factor of Safety…

A: Find the following: - Righting Moment - Overturning Moment - Factor of Safety Against Sliding -…

Q: For a shallow foundation shown below: Estimate the moments about the x- and y-axis; assume that the…

A: Shallow foundation : shallow foundation is a type of building foundation that transfers structural…

Q: Q5: Determine the resultant couple moment acting on the beam. Solve the problem two ways: (a) sum…

Q: A 2.5m x 2.5m square footing supports a 250mm x 400mm column. Given data: Thickness of footing…

Q: 2.2 The following infinitesimal, micro-strain components: ₁1 = 600, 2₂2 = 33 = 0, & 12 = 21 = 200,…

Q: A P 2 ft B 6 ft с 4 ft D

Q: Find H in the figure for Q3 = 20 L/s, 70.

Q: Figure 1 shows a warren truss bridge of span 36m and height 8m. The trusses are spaced at 5m c/c,…

Q: 25. An activated sludge system is designed to treat population of 50 000. The wastewater that enters…

Q: Part 1: Some Discrete Probability Distributions 4.2 Discrete Uniform Distribution 4.3 Binomial…

A: in this question , 3 examples is asked about probability

Q: Estimate the thickness of cement concrete pavement using Pickett's corner load stress equation from…

Q: (1) why the flow faster at the pipe center when you observe few millimeters from the pipe inlet; (2)…

A: Uniform flow If the flow velocity have same magnitude and direction at every point in the fluid it…

Q: H.W2 Determine the maximum deflection of the simply supported beam. E = 200 GPa and I = 39.9(106)…

A: Given data: E = 200 GPa = 2×108 kN/m2 I = 39.9 ×10-6 m4 Steps: 1. To determine support reaction 2.…

Q: B. Write shear and moment equations for the beams in the following problems. In each problem, let x…

Q: What is the maximum diameter of aggregate considering the clear spacing of the reinforcements in mm?…

A: This question is related to The design of Reinforcement concrete structures.

Q: A Determine a position and magnitude of the maximum instantaneous deflection as a result of a…

A: Given Simply supported beam carrying a load of 5 kN/m Cross section b=200mm , d=400mm Therefore…

Q: Design a sliding gate wing type of beams (w8*40) which have an elastic section modulus equal to 582…

Q: (a) X Path 1 a. For the shown figure if the distance at which the travel times for the two paths are…

A: According to top section 19.12.13 of ACI 318-19, The compressive strength shall be based on the 28…

Q: A rectangular channel of planed timber (n = 0.012) is 1.5 m wide and carries 1.7 m³/s. The depth of…

A: Given data: Rectangular channel n= 0.012 b=1.5 m Q= 1.7 m3/s. y1=1.2 my2=0.9 mx=200 m

Q: cal direction with tion in static pre

Q: Determine the member end moments and reactions for the beam for the loading shown in the figure. Use…

Q: SOLVE THE INDETERMINATE STRUCTURE USING CASTIGLIANO’S THEOREM AND SHOW COMPLETE SOLUTIONS.…

Q: the shear-force and bending-moment diagrams for the simply supported beam shown. Determine the…

Q: Wind velocity = 5 kph @ 2 m above ground; Rotor dia. = 3m, & Height of 12 m; Ground roughness - very…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: Using cantilever method, determine the following: Column end moment in FJ, in kN-m.

Q: Without writing the shear and moment equation, use the area method to draw shear and moment…

Q: for the beam shown in the figure, a) find the equation of elastic curve by integration method. b-)…

Concept explainers

Fluid Materials

In general terms, anything that flows can be termed as a fluid. In other words, a fluid is any substance that cannot resist shear forces and deforms continuously under the application of external shear forces. Fluid materials differ completely from solid materials such as metals and alloys. For instance, if we consider two infinitesimally small cross-sectional areas of fluid materials and solid materials, and apply shear forces to these elements, both the elements will undergo deformation. Upon releasing the shear force, the element of the solid materials will regain its original orientation, but the element of the fluid materials will keep on deforming continuously under the action of the shear force.

Question

Solution.

A steel rod of original length 200 mm and final
length of 200.2 mm after application of an axial
tensile load of 20 kN, what will be the strain
developed in the rod?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
Define the below ? Lateral strain is considered – Skempton–Bjerrum method
A high-strength steel band saw, 24 mm wide, runs over pulleys 800 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 280? Assume E = 230 GPa. Answer must %3D be in mm.
Find the strain of a brass rod of length 250mm which is subjected to a tensile load of 50kN when the extension of rod is equal to 0.3mm?
A 12 mm steel bar is hanged vertically as shown and is loaded with a 700 lb weight of scrap materials. Determine the following a) Maximum stress that the steel bar could hold b) Deformation of the steel bar
A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress developed in the rod, in kN/m^2. Is the tensile or compressive? (b) compute the amount of elongation (in mm) in the steel rod caused by the applied load, (c) what will be the elongation (in mm) in the steel rod if the weight of the steel rod is included? Use density of the steel to be 7860 kg/m^3. Young's modulus of elasticity, E=200GPa. W=mg. Draw free body diagram of the steel rod.
Q- A cylindrical piece of steel, with a diameter of 60mm and length 100 mm, is subjected to an axial compressive force of 40,000 kg. If bulk modulus is 1.7 x 106 kg/cm² and poisson's ratio is 0.25 than the change in volume of the cylindrical piece is
A drill rod with a diameter of 12 mm is made of high- strength steel alloy with a shear modulus of 80 GPa. The rod is to be subjected to a torque T. What is the minimum required length L of the rod so that the cross section at one end can be rotated 900 with respect to the other end without exceeding an allowable shear stress of 300 MPa?
What will be the strain induced in a steel rod of length 200 mm that is subjected to a tensile load of 100 kN when the extension of the rod is equal to 0.4 mm ?
A 5ft long bar with a 3in x 5in cross section is subjected to a 13,638lb tensile load. What is the tensile stress in ksi? Answer to two decimal places.
STRENGTH OF MATERIALS (SIMPLE STRAIN: Poisson’s Ratio: Biaxial and Triaxial Deformations)100% UPVOTE! PLEASE INCLUDE FBD IF NECESSARY. THANK YOU! GOD BLESS!