5 A load of 15 kN is applied to a M 30 x 2, Class 10.9 bolt that is used to clamp two aluminummembers each having a thickness of 10 cm.Determine: Joint separation and bolt failure safety factor if joint stiffness is thrice the bolt stiffness andthe connection is reused.

Given that, t=10cm=100mm and l=2t=2×100=200mm it is given that bolt is M30, for M30 bolt H=25.6cm…

Answered: A load of 15 kN is applied to a M 30 x…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve for the tensions 45 50 g
Question 3) The length L is given as L=34 m on the plate in the figure. According to this;Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)Question 3-B) Find the Y coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)
%3D Consider for the part in the figure below, a =112, b= 60 and c= 104. b. b 40 80 20 45 Dimensions in mm Analyze the part in order to calculate the coordinates of the centre of gravity in the (z, y, z) system of coordinates. It is essumed that the following process was following for the manufacturing process • Part 1(a cubic piece of dimension 37 x 60 x 60 is cut out of a Part 2 of dimensions 149 x 60 x 80 and then • Part 3 (triangular prism) is welded Part 2
If Gear C and gear A are having the same pitch diameter gear and gear B is twice (larger) the diameter of gear C. If gear C is turning at the speed of 50 RPM, what would be the Rotational speed of Gear B in RPM. (RPM = revolution per minute)
4. What is the cost of 23' of cable if 34' costs $76.00? (round to nearest dollar)
I didn't understand how you find the angle Alpha = 21.63
Topic: Gear complete the table below. Answer only no. 9-11 in the table.
A5C) Concurrent forces.. O a. act on the same line O b. act on the same plane O c. pass through same point O d. None of the these a hp
Find x and y of the given figure. Make a table of values for each shape and show complete solution. *10 in 40 in 8 in -20 in 15 in
3. Determine the displacement of an eight-cylinder engine having a bore of 3.25 in and a stroke of 3 in.
What is the resulting angle in radian with 2 decimal places if the complex number is 1+3 j
Determine the distance from the x-axis to the center of the hole in inches.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A load of 15 kN is applied to a M 30 x 2, Class 10.9 bolt that is used to clamp two aluminum members each having a thickness of 10 cm. Determine: Joint separation and bolt failure safety factor if joint stiffness is thrice the bolt stiffness and the connection is reused.