G Determine the equillalent. tiffness for the dreegreem

Q: dr. リ+ y + tan²t – 1 dt dy dt =-+tant 山一位

A:

Q: mensions a tonnage to E the part if the desity

A: Given compaction pressure = 1000 MPa Surface area of the component = π4652- 202 mm2 We know that Pr…

Q: Find pressure the pistoni

A: Given data;  Piston diameter,d=30 cm Force,F=3000NFind pressure on the piston ?

Q: centr the the special case 2 -a) 20h

A: Given data Geometry is given Required Y bar

Q: State the difference between the eutectic and eutectoid points.

A: Eutectic point: In the iron carbon phase diagram at 2 percentage of carbon is called eutectic point.…

Q: SHOW COMPLETE SOLUTION PLS NOTE: THE ANSWER IS SHOWN IN THE PICTURE

A:

Q: C 3 ft

A: Writing the co-ordinates of different points – The position vector

Q: tance travelled and is given icle is given by: 200s -s²)

A: we know that  a= dv/dt dv = a*dt

Q: A section of a hot water heating system must be suspended. The section ismade from one-inch copper…

A: given:copper tube weight W=8.515poundwater weight w=4.65pound

Q: Determine its minimum required diameter

A: for solution refer below images.

Q: ensity of Helium is one s <g/m Determine the buc

A:

Q: 50gm when quenched in water en the temperature of the ball a

A:

Q: hing 3304 kN is If the block is 9

A: Weight of block = 3304 kN Weight of sea water displaced = volume of water x density Volume of water…

Q: Q34 gine exCumphe far nolineer operautor an

A: Given: To give an example of non-linear operator.

Q: -4 cm inner diameter from

A:

Q: is it dinegerce ?

A: To find  Convergence or divergence

Q: 4y" + y = 0,

A: Dear Student  as per bartleby guidelines I am allowed to answer first question only . Please post…

Q: 1,500 mm (1) 900 mm (2) (2) A C

A:

Q: Find the welouty f flay A=2.1m2 = २० 0[S

A: Introduction : The question is related with fluid mechanics . In this question we are provided with…

Q: and the

A:

Q: Deive equabon for height Rof Pate Governer useig Instantenous Centre Method.

A:

Q: Determine the total increase in length.

A: Given: E1=175 GPa E2=210 GPa P=55 kN To determine: Total increase in length

Q: L,=40mm; L,= 120mm; L,=80mm L=100mm and 0,=65°. Find the possible value of 0, and and 0,

A:

Q: Whyar 1 75kum Im D

A:

Q: ngth Land flexura Gon of the free en

A:

Q: A: Determine (h) and ge pressure (A&B), if gage pressure at (A) creased by 45% from

A:

Q: Tong ransfer c of secc nionor

A:

Q: of the block if 60 °F (C

A: given:μ=0.76N/sm2m=10kgθ=200y=0.1mm

Q: y. what is the change in length in mm? k for =

A: Need to find change in length.

Q: au that the gan AS = 3 Mcn taT

A: Entropy defines the randomness of the system. It measures the thermal energy of a system per unit…

Q: e CLA over length L?

A: 2 μm.

Q: Find the affrienyg does SooS og waik ų mfut wank ub 2600 J a maehine that

A: Given data : Input work=2600 J Output work=900 J   Required : Efficiency of machine

Q: =D and F13 tube shown.

A: Given data F13 = 0.17 Length of cylinder = diameter of the cylinder

Q: ith both ends open is 0.85 m long. Assumin

A: f3=600Hz

Q: the gas pressure inside the cy

A: To find  gas pressure inside the cylinder

Q: The fol

A: option (c) all of these   ,  is correct

Q: Find the tensien force in each 35 eable. A

A:

Q: nicle is given by: 200s – s2)

A: We know that  a= dv/dt dv= a. dt

Q: are such. nd thei- nei: ular to

A:

Q: Find the value of Pmax if the the

A: need to find Pmax

Q: Both made up of same material and

A:

Q: Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pr

A: Given Data⇒ Cast iron cylinder Diameter of cylinder(d)=250 mm Pressure (P)=0.7 Nmm2 Maximum tensile…

Q: Demie me reuta INT he Ta n hoen in

A: The resultant of the two forces is R=4002+6002+2400600cos180-60=529.150 N

Q: The value of surface tension is less at O 50 oC O 80 oC 103 OF 3000C O No correct answer

A: In this problem, it is asking about the surface tension of water.

Q: Q1: Find the pressure at A and B of the air.

A:

Q: using multip de atog. estrac per hour n. hun ane contain a tounter cuurent mual ret ain s 2 kg of…

A: Tung meal=55% oil m=4000kg/hrsolvent=5%wt of oilretains=2kg of solvent To-Find:- Theoretical number…

Q: ment at midspan (in kip-ft to one decimal) for the following bear kip/ft, L = 26 ft, and a = 6 ft.…

A:

Q: The best approximation for a,

A: Given data, Flywheel having mass=m Rim of radius=RConcentric disk like feature of radius=R/2Flywheel…

Clutches, Brakes, Couplings, and Flywheels

The clutch is described as a machine element used to connect or disconnect two shafts together to transmit torque or power. The clutch works on the principles of friction. The clutch is commonly used in automobiles to transfer power from the driving shaft to the driven shaft.