3-9. Solve for the algebraic sum of the moments in pound-feet about A when h is 20 m as shown in Figure 13-39.

Q: 2. The system of figure has degrees of freedom. ---- --- Fork Joiet Two Three Four Soring Slider…

A:

Q: В TA A OB

A: For solution refer below image.

Q: In the figure shown, Q2A = 3 inches, and AB = 9 inches. A. Draw the four bar linkage of this…

A:

Q: can you help me to do the position analysis of this mechanism and find the mathemetical expressions…

A: Given:To find:Draw the position analysis and find the angle values.

Q: E 3

A:

Q: 2. Three bars, hinged at A and D and pinned at B and C as shown in Figure 1-60, form a four link…

A: Given   Force, F = 20 kN      Angle = 45o Find   Another force, P

Q: iii) Specifications: Length (in) Theta Degrees (*) Link LI 3.00 L2 6.38 25 La 4.00 L4 4.50 L3 L4 L2…

A:

Q: Number of teeth of gears z1: 22 Tooth numbers of gears z2: 90 Tooth numbers of gears z3: 23 Tooth…

A: Here motor is driving the gear 1 shaft which is in mesh with gear 2. Gear 2 and 3 are at same shaft…

Q: Find the degrees of freedom of the following two different links Pin in slot b.

A: Solution:

Q: mm.

A:

Q: 13-10. Solve for the algebraic sum of the moments about the center of the axle shown in Figure…

A:

Q: 300N forces on the pliers? 300N What forces are exerted on the bolt at E in the figure below as a…

A: Given: Force on the pliers, Fp = 300 N Required: Fb ( force exerted on the bolt at E )

Q: S Q2. The double pulleys are fastened together to form a rigid unit. If V₁ = 9 and VB = 3 compute…

A: The answer is given in the below

Q: There is a pirate ship in the harbor which features a large, cast iron wheel that is used to steer…

A: External torque  Tpush=33.7Nmresisting torque Tre=10Nmso the net torque acting on the wheel…

Q: .3 m B 5 kN 75 A 2 kN .5 m 2 kN FIGURE P3-21 -2m- 3-22. Determine the moment about point A for the…

A:

Q: 2. Three bars, hinged at A and D and pinned at B and C as shown in Figure 1-60, form a four- link…

A: Given   Force, F = 20 kN      Angle = 45o Find   Another force, P

Q: In the figure, cables AD, AB and AC are needed to support the 60lb box. Determine the coordinates of…

A:

Q: I want the force for A and B by using the centroid or solve it by the right way

A:

Q: Please solve in handwritten format. Include free body diagram.

A: Step 1:

Q: In an open belt drive, two sheaves have diameters of 5 in. and 12 in. Determine the center distance…

A: Write the given data with suitable variables: d1=12 ind2=5 inL=72 in

Q: 2-50. The overhead crane shown has a rated capacity of 500 tons. Find the moment of this load about…

A: To Find : The moment of this load about A. Given : The capacity of load is P=500 tons The distance d…

Q: 5-4 Locate the center of mass for the four particles shown. in Fig, P54 if m= 16 kg, mg = 24 kg, mc…

A: Given data: The center of mass of each particle with respect to the origin is

Q: 3-25. The bucket shown in Figure P3-25 pivots at A and has the forces shown acting on it. Deter-…

A: To find: The moment about the point A. FBD: The free body diagram is shown below: Here, FH is force…

Q: Q1: Find the torque of the force 800 N in figure (1) about point 0.

A:

Q: Solve the problem. A 11-in. connecting rod in an engine connects the wrist pin of a piston at point…

A:

Q: 4-3. Draw a free-body diagram of member BD in Figure P4-3. 10 40 mm 60 mm mm B 50 N 15 mm 15 mm…

A: Free body diagram (FBD): The diagram of any object which shows the externally applied forces and…

Q: .  Compute the reactions at the supports 2.  Draw the complete shearing force and bending moment…

A:

Q: Find the moment (Nm) caused by the force F = 239 N about point O if a = 24 mm and b = 34 mm. Round…

A:

Q: Draw the figure and show your solutions. PLEASE ANSWER IT ASAP FOR AN UPVOTE.   Shafts A and B are…

A:

Q: The length of the links are known for the mechanism shown in Figure. The angle of  driver link 1…

A: The number of links is n=6 The number of binary joints is J1=7 The number of higher pairs is J2=0…

Q: The figure shows a rotating geared system. A torque of 3N is applied to an input gear in order to…

A: Given data: Input gear teeth = z = 11 Output gear teeth = Z = 99 Assuming that  Input gear torque =…

Q: Given: L¡ = 7.25 in., L2 = 2.00 in., L3 = 7.00 in., L4 = 4.50 in., 01 = 5°, and 02 = 150°.…

A:

Q: Find the value of the input torque on the crank-shaft mechanism in followin Figure. The centers of…

A: To carry out dynamic force analysis of the four-bar mechanism shown in the figure, it is required to…

Q: Determine the equivalent spring constant (N/m) of the whole system shown if k1 = 19.69 N/m, k2=…

A: k1= 19.69 N/m k2= 27.45 N/m k3= 38.96 N/m k4= 45.2 N/m k5=58.63 N/m

Q: Calculate the moment about point A in Figure P3-5. 800 lb 200 lb 14 3. 5'- 400 lb

A: To determine the point about Point A.

Q: 600 lb FOR -6 ft -6 ft 7200 lb-ft 12 ft 150 lb/ft B

A:

Q: 3-23. Determine the moment about point A due to the forces shown in Figure P3-23. 100 lb 2 60 lb 80…

A: Given question: We have to find the moment about point A.                                       […

Q: 6 in 60° 20 in Statics Instructor A vertical force of P = 100 lb is required to remove the nail at C…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.