A liquid of density (ρ = 1.65 kg.m3) flows through two horizontal sections of tubing with different diameters. In the first section, the cross-sectional area is 10.0cm2, the flow speed is 275cm.s-1 and the pressure is 1.20 x 103Pa.In the second section, the cross-sectional area is 2.50cm2. Calculate the following for the second section of the tube: flow speed in cm.s-1 and pressure

A liquid of density (ρ = 1.65 kg.m3) flows through two horizontal sections of tubing with different diameters. In the first section, the cross-sectional area is 10.0cm2, the flow speed is 275cm.s-1 and the pressure is 1.20 x 103Pa.In the second section, the cross-sectional area is 2.50cm2. Calculate the following for the second section of the tube: flow speed in cm.s-1 and pressure

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter15: Fluids

Section: Chapter Questions

Problem 44PQ: Water enters a smooth, horizontal tube with a speed of 2.0 m/s and emerges out of the tube with a...

See similar textbooks

Similar questions

Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius of 0.312 m at a velocity of 1.64 m/s. a. What is the velocity of the waste after it goes through a constriction and enters a second section of pipe with a radius of 0.222 m? b. If the waste is under a pressure of 850,000 Pa in the first section of pipe, what is the pressure in the second (constricted) section of pipe?
A horizontal pipe 10.0 cm in diameter has a smooth reduction to a pipe 5.00 cm in diameter. If the pressure of the water in the larger pipe is 8.00 104 Pa and the pressure in the smaller pipe is 6.00 104 Pa, at what rate does water flow through the pipes?
The small piston of a hydraulic lift (Fig. P15.6) has a cross-sectional area of 3.00 cm2, and its large piston has a cross-sectional area of 200 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 15.0 kN? Figure P15.6
Review. The tank in Figure P15.13 is filled with water of depth d = 2.00 m. At the bottom of one sidewall is a rectangular hatch of height h = 1.00 m and width w = 2.00 m that is hinged at the top of the hatch. (a) Determine the magnitude of the force the water exerts on the hatch. (b) Find the magnitude of the torque exerted by the water about the hinges.
Water enters a smooth, horizontal tube with a speed of 2.0 m/s and emerges out of the tube with a speed of 8.0 m/s. Each end of the tube has a different cross-sectional radius. Find the ratio of the entrance radius to the exit radius.
What fraction of ice is submerged when it floats in freshwater, given the density of water 0°C is very close to 1000 kg/m3?
Mercury is poured into a U-tube as shown in Figure P15.17a. The left arm of the tube has cross-sectional area A1 of 10.0 cm2, and the right arm has a cross-sectional area A2 of 5.00 cm2. One hundred grams of water are then poured into the right arm as shown in Figure P15.17b. (a) Determine the length of the water column in the right arm of the U-tube. (b) Given that the density of mercury is 13.6 g/cm3, what distance h does the mercury rise in the left arm?
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate be new flow rate for following changes with all other factors remaining the same as in original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid wit 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube used with a 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half length, and pressure difference is increased by factor of 1.50.