Question
thumb_up100%
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by stepSolved in 2 steps
Knowledge Booster
Similar questions
- A rock displaces 0.6 m3 when it is fully submerged in WATER (D = 1 kg/L). What is the volume of the rock? Express your answer using appropriate mks units.arrow_forwardIn a hydraulic lift, the radii of the pistons are 2.11 cm and 10.0 cm. A car weighing W = 10.0 kN is to be lifted by the force of the large piston. A) What force Fs must be applied to the small piston? in N B) When the small piston is pushed in by 10.0 cm, how far is the car lifted? in mm C) Find the mechanical advantage of the lift In numeric Responsearrow_forwardA cylindrical container with a cross-sectional area of 66.2 cm² holds a fluid of density = 943 kg/m³. At the bottom of the container the pressure is 114 kPa. Assume Pat 101 kPa. What is the depth of the fluid, in meters?arrow_forward
- The entrance opening of a horizontal pipe has a radius of 6 cm and water is flowing at .35 m/s. The pressure at opening is 18.5 n/m2 and changes to 23.0 N/m2 at the exit. What is the area of the exit opening?arrow_forwardPlease help thank you!arrow_forward1. A capillary tube of inside diameter d=6mm connects tank A and open container B as shown in Fig.2. The liquid in A,B and capillary CD is water having a specific weight y=9780 N/m³ and a viscosity of μ=0.0008N s/m². The pressure PA-34.5 kPa gage. Neglecting the minor losses at C and D, determine the flow rate Q through the capillary tube. Assume laminar flow from A to B and use h=32μLV/yd² for the friction loss, where V is the water velocity through the capillary tube. (2) Container B 1.4 m Datum 1-4.3 m 45° D (1) Air Tank A Im 200151816arrow_forward
- A water intake at a pump storage reservoir (see the figure below) has a cross-sectional area of 0.637 m². The water flows in at a speed of 0.470 m/s. At the generator building, at distance D = 156 m below the intake point, the cross-sectional area is smaller than at the intake and the water flows out at 9.44 m/s. What is the difference in pressure between inlet and outlet? Reservoir Number 202.6 Units D Intake MPa Generator building Outlet-arrow_forwardA container of water has a cross-sectional area of Ac=0.25m2. A piston with mass mp=18kg, sits on top of the water as shown in Figure 1. The height of the water which the piston is sitting on is h1=0.45m. There is a spout located h2=0.17m from the bottom of the tank, open to the atmosphere, and a stream of water exits the spout. The cross-sectional area of the spout is As=8.5 x 10-3m2. A valve on the spout is closed. How much force is the water in the spout exerting on the valve?arrow_forwardA cylinder that is hi = 18.5 cm tall and open on top is filled with water. If a hole is made in the side of the cylinder, Ah Ah = 3.40 cm below the top level, how far x from the base of the cylinder will the stream land? h, Assume that the cylinder is large enough so that the level of the water in the cylinder does not drop significantly. cmarrow_forward
- A paperweight, when weighed in air, has a weight of W = 4.65 N. When completely immersed in water, however, it has a weight of Win = 3.43 N. Find the volume of the paperweight. water Number i eTextbook and Media Units +arrow_forward3. ANSWER PLEASEarrow_forwardA liquid is flowing through a horizontal pipe whose radius is 0.0301 m. The pipe bends straight upward through a height of 8.80 m and joins another horizontal pipe whose radius is 0.0726 m. What volume flow rate will keep the pressures in the two horizontal pipes the same? Number Units 202arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios