A jet of water from a fixed nozzle has a diameter of 25 mmand strikes a flat plate at an angle of 30° to the normal to theplate. The velocity of jet is 5 m/s and surface of plate infrictionless. Calculate the force exerted normal to the plate :(i) If the plate is stationary and(ii) If the plate is moving with a velocity u of 2 m/s in thesame direction as the jet.Jet30e = 60%3DV sin 030V

We know that a fixed nozzle's water jet has a diameter of 25 mm and impacts a flat plate at a 30o…

A jet of water from a fixed nozzle has a diameter of 25 mm and strikes a flat plate at an angle of 30° to the normal to the plate. The velocity of jet is 5 m/s and surface of plate is frictionless. Calculate the force exerted normal to the plate : (i) If the plate is stationary and (ii) If the plate is moving with a velocity u of 2 m/s in the same direction as the jet. Jet 30 e = 60 %3D V sin 0 30 V

A jet of water from a fixed nozzle has a diameter of 25 mm and strikes a flat plate at an angle of 30° to the normal to the plate. The velocity of jet is 5 m/s and surface of plate is frictionless. Calculate the force exerted normal to the plate : (i) If the plate is stationary and (ii) If the plate is moving with a velocity u of 2 m/s in the same direction as the jet. Jet 30 e = 60 %3D V sin 0 30 V

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The entrance flow between two parallel plates (gap h) has a velocity that varies linearly at the entrance and develops into a fully parabolic profile at the exit. What is the relationship between the maximum velocity at the entrance and that at the exit? You can show by symmetry that the maximum velocity is attained at the mid-plane between the two plates.
A horizontal jet of water (at 10°C) that is 6 cm in diameter and has a velocity of 20 m/s is deflected by the vane as shown. If the vane is moving at a rate of 7 m/s in the x-direction, what components of force are exerted on the vane by the water in the x- and y-directions? 45°
A 3-in diameter horizontal water jet having a velocity of 140 ft/s strikes a curved plate, which deflects the water 180 degrees at the same speed. Ignoring the frictional effects, determine the force required to hold the plate against the water stream. Please no conversion need it, only the 3in into .25feet, please. for me, I got 3.71KN on the x-axis.
A jet of water of diameter 75 mm moving with velocity of 25 m/s strikes a fixed plate in such a way that angle between jet and plate is 60°. Find the force exerted by jet on plate. in the direction normal to plate (1) (ii) in the direction of jet. V cos 0 V sin 0 V Fn F,
Two horizontal plates are spaced 3 in. apart. The spacebetween the plates is filled with mercury at 90 ° F . The upper plateis moving at 3 ft /sec, (a) Why does the liquid velocity vary linearly between the plates ? (b ) Calculate the shear stress at a plane 1 in. from the slowermoving plate.(c) Calculate the momentum flux at the surface of the fastermoving plate.
A horizontal pipe ends with a nozzle that discharges to the atmosphere. The pipe has adiameter of 8cm and operates with a velocity of flow equal to 7.5 m/s. What diameter ofnozzle is required to obtain a jet with a velocity of 60 m/s?What is the water pressure in the pipe (assuming no energy losses)? What is the force exertedby the water on the nozzle
The jet engine on a test stand, shown in the figure, admitsair at 20oC and 1 atm at section 1, where the area is 0.5 m2and the velocity is 250 m/s. The fuel-to-air ratio is 1:30.The air leaves at section 2 at atmospheric pressure and ahigher temperature. The exit velocity is 900 m/s and thearea is 0.4 m2. Compute the horizontal test stand reactionRx needed to hold the engine fixed.
A cart with frictionless wheels and a large tank shoots water at a deflector plate, turning it by angle ? as sketched. The cart tries to move to the left, but a cable prevents it from doing so. At the exit of the deflector, the water jet area Ajet, its average velocity Vjet, and its momentum flux correction factor ?jet are known. Generate an expression for the tension T in the cable in terms of the given variables.
COnsider an airplane flying at a standard altitude of 6km with a velocity of 330m/s. At a point on the wing of the airplane, the velocity is 400m/s. Calculate the pressure at this point. Cp=1008 j/kgK. answer should be in metric. and detailed solution.
8-2 For this weird nozzle, what force would have to be applied through the bolts in the flange to hold the nozzle in place? Assume irrotational flow. Water is flowing, and the nozzle itself weighs 200 N. Apipe = 0.10 m² -40 cm- Vjet= 30 m/s Ajet = 0.01 m² V₁= 30 m/s A₁ = 0.01 m²
jet of water of diameter 100 mm strikes a curved plate at its center with a velocity of 15 m/s. The curved plate is moving with a velocity of 7 m/s in the direction of the jet. The jet is deflected through an angle of 150°. Assuming the plate smooth find: (i) Force exerted on the plate in the direction of the jet. (ii) Power of the jet, and (iii) Efficiency.
A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd.CHOICES a.0.989 b.0.98 c.0.629 d.0.636