8-2 For this weird nozzle, what force would have to be applied through the bolts in the flange to hold the nozzle in place? Assume irrotational flow. Water is flowing, and the nozzle itself weighs 200 N. Apipe = 0.10 m² -40 cm Vjet = 30 m/s Ajet = 0.01 m² V₁=30 m/s A₁ = 0.01 m²

8-2 For this weird nozzle, what force would have to be applied through the bolts in the flange to hold the nozzle in place? Assume irrotational flow. Water is flowing, and the nozzle itself weighs 200 N. Apipe = 0.10 m² -40 cm Vjet = 30 m/s Ajet = 0.01 m² V₁=30 m/s A₁ = 0.01 m²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A ball weighing 1 kg is “floating" on a circular jet, as shown in the figure (ignore the wire, which is there to stabilize the weight). The jet leaving the orifice at the bottom has an upward velocity of 10 m/s, and the jet diameter at the exit is 2 cm. Assuming the jet spills sideways at 90°, find the height h at which the ball will float. Jet D1 =0.02 m W1 = 10 -
A teenager is stealing gasoline from his father's car with a siphon with diameter of 10 mm. The heights in the figure are: z1 = 853 mm and 22 = 92 mm Calculate the volumetric flow rate out of the tank. Round off the answer to two decimal digits in l/s, but enter your answer without the unit. Z₁ 22
What will be the new pressure exerted by a fluid flowing through a horizontal pipe with an initial speed of 3 m/s and pressure of 100 kPa, if this fluid starts flowing at a speed of 15 m/s? (density of fluid =850 kg/m^3)
Prob 4.Draw fbd.
Plz solve correctly
Please explain on how to get the theta, Qin and Qout. It should be theta = 54.2461 deg Q in = 0.0382 m3/s Q out = 0.0191 m3/s my professor said. but I don't have solution. used 9.807m/s² not 9.81.. thank you
As6. N=35 N2=16 N3=16
A horizontal 300-mm pipe contracts to a 150-mm diameter. If the flow is 0.127 m3/s of oil (s.g.=0.88) and the pressure in the smaller pipe is 265 kPa what force is exerted on the contraction, neglecting friction?
Problem 2. An engineer helps with the design of a rotating spray for a dishwasher. The spray has 4 identical jets spaced equally around the rim of a disc. Water enters though a hollow shaft and then flows radially out to the jets. The nozzle of the jet has a diameter D of 0.3 cm and makes an angle a = I (3 with the horizontal plane of the disc(See figure). The jets are oriented so that v2r=0. If the total flowrate Q=50 mL/s and the disc has radius R= 7.5 cm, determine the torque in dyne-cm required to keep the disc from rotating. Water jet R. Water flows radially inside dise to jet Water in View from top View from side
6.5 BELLOWS 6100mm The horizontal elbow is joined by bellows to the rest of the piping system and it transports water. Determine the X and Y components of the force needed to keep the elbov in posi- tion. The pressure at A and B is 200 kPa, the flow rate is 30 L/s and the pipe diameter is 100 mm. 6.6 Water flows at a rate of 0,055 m³/s through a piping system and then issues from the pipe of 50 mm diameter into the atmosphere. Ø150mm Ø50mm Ignore losses in the pipe and determine the force required at the flange to keep the nozzle in position. (Hint: first determine the pressure at A with Bernoulli's equation.)
a=2 , b=1 The properties of the air in the inlet section with A1 = 0.25ab m2 in a converging-diverging channel are given as U1 = 25a,b m/s, T1 = 3ab K, P1 = 13a,b kPa (absolute). Find the required cross-sectional area, pressure, temperature, velocity and mass flow rate to obtain sonic (Ma2=1.0) flow at the outlet. Calculate critical values of A*, U*, T*, P*. Solve the problem by making the necessary assumptions and drawing the schematic figure.
kg Water (p = 1000- -) flows through the elbow below. The diameter of both the inlet and outlet is 1.1 cm, and the velocity through the nozzle is V =4.5 m/s. The outlet m³ has an angle of 0 =15 degrees. The water is at a pressure of 29 kPa (gauge). Find the magnitude of the force on the elbow. 0 V