A hollow shaft made from AISI 4340 steel has an outer diameter D. of 4 in. and an innerdiameter Di of 2.5 in. The shaft rotates at 46 rpm for one hour each day. It is supportedby two bearings and loaded in the middle with a load W of 5500 lbf. The distance betweenthe bearings Lis 78 in. The maximum tensile stress due to bending for this type of cyclicloading is calculated using the following equation:8WLD,#(Dg – D{)What is the stress ratio for this type of cyclic loading? Would this shaft last for one yearassuming a safety factor of 2?

Answered: Image /qna-images/answer/6312bb32-b348-43c2-89f1-1d2a9da115c1.jpg

A hollow shaft made from AISI 4340 steel has an outer diameter Do of 4 in. and an inne diameter Di of 2.5 in. The shaft rotates at 46 rpm for one hour each day. It is supporte by two bearings and loaded in the middle with a load W of 5500 lb:. The distance betwe the bearings Lis 78 in. The maximum tensile stress due to bending for this type of cycl loading is calculated using the following equation: 8WLD. #(D; – D{) What is the stress ratio for this type of cyclic loading? Would this shaft last for one ye: assuming a safety factor of 2?

A hollow shaft made from AISI 4340 steel has an outer diameter Do of 4 in. and an inne diameter Di of 2.5 in. The shaft rotates at 46 rpm for one hour each day. It is supporte by two bearings and loaded in the middle with a load W of 5500 lb:. The distance betwe the bearings Lis 78 in. The maximum tensile stress due to bending for this type of cycl loading is calculated using the following equation: 8WLD. #(D; – D{) What is the stress ratio for this type of cyclic loading? Would this shaft last for one ye: assuming a safety factor of 2?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.12.3P: A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0...

See similar textbooks

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
Repeat Problem 10.3-15 using L = 3.5 m, max = 3 mm, and EI = 800 kN·m2.
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A solid circulai' aluminum bar AB is fixed at both ends and loaded by a uniformly distributed torque 150N·n/m. The bar has diameter d = 30 mm. Calculate the reactive torques at the supports and the angle of twist at midspan. Assume that G = 28 GPa.
A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The inside diameter of the shaft is to be one-half of the outside diameter. If the allowable shear stress in the shaft is 45 MPa, what is the minimum required outside diameter d?
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
Compare the angle of twist 1 for a thin-walled circular tube (see figure) calculated from the approximate theory for thin-walled bars with the angle of twist 2 calculated from the exact theory of torsion for circular bars, Express the ratio 12terms of the non-dimensional ratio ß = r/t. Calculate the ratio of angles of twist for ß = 5, 10, and 20. What conclusion about the accuracy of the approximate theory do you draw from these results?
A solid circular shaft AB of diameter d is fixed against rotation at both ends (sec figure), A circular disk is attached to the shaft at the location shown. What is the largest permissible angle of rotation 0max of the disk if the allowable shear stress in the shaft is Tallow? [Assume that a >b. Also, use Eqs. (3-50a and b) of Example 3-9 to obtain the reactive torques.]
Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Answer in Word please
Design a rigid flange coupling to transmit a torque of 228N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa > Provide FBD
Design a rigid flange coupling to transmit a torque of 250N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Torque = 257N-m