A solid uniform shaft of circular crosS sec- tion is subjected to a maximum bending moment of 3 kNm and a twisting moment of 4 kNm. The shaft material has an alternate tensile stress of 720 N/mm? and ultimate shear atress of 500 N/mm?. Determine the shaft diameter required for a factor of safety of 6.

A solid uniform shaft of circular crosS sec- tion is subjected to a maximum bending moment of 3 kNm and a twisting moment of 4 kNm. The shaft material has an alternate tensile stress of 720 N/mm? and ultimate shear atress of 500 N/mm?. Determine the shaft diameter required for a factor of safety of 6.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.5P: A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used...

See similar textbooks

Similar questions

What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
Q3/A solid circular shaft is subjected to a bending moment of 3000 N.m and a torque of 10000 N.m. The shaft is made of 45 C 8 steel having tensile stress of 116 MPa and a shear stress of 83 MPa. determine the diameter of the shaft.
The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the allowable stress in shear is 60 MPa, whatis the maximum permissible torque Tmax that may beexerted with the wrench?Through what angle f (in degrees) will the shafttwist under the action of the maximum torque?(Assume G = 78 GPa and disregard any bending ofthe shaft.)
A solid shaft is subjected to a twisting moment of 150 kNm. If the angle of twist is 8º per meter of the shaft and the shear stress is not to exceed 550 MPa. Determine the suitable shaft diameter by comparing the strength design and rigidity design. Also, determine the maximum shear strain acting on the shaft. Take G 250 GPa. Diameter of shaft based on Strength design is in mm Diameter of shaft based on rigidity design is in mm The sutable Diameter of the shaft is in mm The maximum shear strain is
Consider the case of shafts subjected to combined twisting moment and bending moment. A solid circular shaft is subjected to a bending moment of 2800 Nm and a torque of 10,000 Nm. The shaft is made of 45 C 8 steel having ultimate tensile stress of 700 MPa and ultimate shear stress of 500 MPa. Assuming a factor of safety as 5, determine, the diameter of the solid circular shaft. if a hollow circular shaft is to be used in place of the solid shaft, find the inside and outside diameter when the ratio of inside to outside diameter is 0.5.
A alm T 1.20 m T B 1.20 m C 3 T The 60 mm diameter shaft is made of 6061-T6 aluminum having an allowable shear stress of Tallow 80 MPa. Find the corresponding angle of twist of disk A relative to disk C. Note: You will need to calculate the maximum allowable torque T first. Provide your answer for angle of twist in radians with 3 significant figures after the decimal point.
Torsional T is applied to the hollow axis (G=80 GPa). Ewha Womans University, the maximum shear strain is γmax = 640 × 10-6rad Igo, inside andThe outside diameters are 120mm and 150mm, respectively.a. What is the maximum axial strain?b. Maximum axial stress?c. What is the maximum torque (T) meeting the above conditions?
A shaft required to transmit 50kW of power will be running at 100rev/min. The maximum twist in 3m length of the shaft is limited to 1.5 degree. If the maximum torque is 30 percent more than mean or average torque. Assume entirely elastic action and take modulus of rigidity for the shaft material G = 135 GN/?2. Determine the following:a. Diameter of the shaft.b. Maximum shear stress developed in the shaft. I need answer ASAP. Thank you!
complete solution A solid steel shaft must not twist through more than 30 in a 6-m length whented to a torque of 12 kN • m. (a) Find the diameter of the smallest shaft thatcan be used. (b) What is the maximum shear stress in the shaft of this diameter? UseG = 83 GPa for steel.
A hollow bronze shaft of 75 mm outer diameter and 50 mminner diameter is slipped over a solid steel shaft 50 mm indiameter and of the same length as the hollow shaft. The twoshafts are then fastened rigidly at their ends. Find the maximumshearing stress developed in the bronze by end torque of 3 kN.mFor bronze G = 35 GPa and for steel G = 83 GPa.