is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Torque = 257N-m

is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Torque = 257N-m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Related questions

Q: The end of a 2.5 in diameter steel shaft is milled to two flats (one flat on the top and one flat at…

A: Given data as per question Diameter of shaft =2.5 in Length of shaft =2 in Torque applied =750 lb.in…

Q: Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is…

A: This is a problem of indeterminate beam, so we can calculate the reactions at A and B. These…

Q: A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in…

A: Coupling : It is a mechanical element which connect the shaft from another also it is used to…

Q: Two short shafts having identical diameters of 35 mm and rotating at 1000 rpm are connected by a…

A: Disclaimer: Since you have posted multiple questions we will solve the first question for you. If…

Q: A round steel shaft transmits 0.75 Hp at 1750 rpm. The shaft is subjected to torsion only and the…

A: Given: Power Transmitted P = 0.75 Hp Speed N =1750 rpm The shaft is subjected to torsion only.…

Q: Problem #1. The 60-mm diameter shaft is subjected to torques as shown. If the applied allowable…

Q: Solve the following problem Two designs for a shaft are being considered. Both have an outside…

A: Shear stress for solid shaft is given as τ=16*Tπ*d3=16*325*1000π*703=4.825 MPa Shear stress for…

Q: The figure below shows a shaft of three segments. It is restrained (fixed support) at both sides and…

A: Bronze: Length, Lbronze= 2 mDiameter, Dbronze= 25 mm= 25×10-3 mGbronze= 35 GPa= 35×109 Pa Aluminum:…

Q: At a machined shaft shoulder the small diameter d is 1.100 in, the large diameter D is 1.65 in, and…

Q: Find the diameter of a solid steel shaft to transmit 18 kW at 990 r.p.m. The ultimate shear stress…

Q: A hollow simple supported shaft 3m made of steel with di/do of 0.6. The shaft is subjected to a…

A: Given: Length of the shaft=3mDiDo=0.6 or Di=0.6DoBending moment (M)=4kNPower tranmitted…

Q: A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig.…

A: Diameter D = 450 mm Kb = 2 Kt = 1.5

Q: Given the figure shown below, bronze and aluminum compound shaft are attached to rigid supports. The…

A: To find: The maximum torque carried by the aluminum shaft. Given: The diameter of bronze shaft is…

Q: afts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft…

Q: In a gearbox, a spur gear is mounted on a shaft at equal distances from two supporting bearings. The…

A: Hghh

Q: A keyed sprocket delivers a torque of 778.8 N - m thru the shaft of 54 mm OD. The key thickness is…

Q: Q.4. A solid steel shaft 5m long is stressed to 80 MPa when twisted through 4 degrees using G- 83…

Q: Design a cast iron driven pulley to transmit 20 kW at 300 r.p.m. The diameter of the pulley is 500…

A: Given data as per question Power transmitted =20 kw speed =300 rpm Diameter of pulley =500 mm Radius…

Q: What is the maximum power P (kW) that can be transmitted by a shaft hollow (do = 50 mm, di = 40 mm)…

A: Outer diameter of shaft= 50mm Inner diameter of shaft= 40mm Rotational Speed of shaft= 600 rpm…

Q: A flanged bolt coupling consists of eight – 10mm diameter steel bolts on a bolt circle 500mm in…

Q: A hollow shaft made from AISI 4340 steel has an outer diameter Do of 4 in. and an inne diameter Di…

Q: Problem 3 A solid shaft is designed to transmit 60kW of power at a speed of 300 rpm. Knowing that…

Q: Problem 10.2. A stepped steel shaft with diameters d, = 56 mm and d = 52 mm is twisted by torques T1…

A: d1 = 56 mm d2 = 52 mm T1 = 2.5 kN.m T2 = 1.5 kN.m

Q: Design a cast iron protective flange coupling to connect two shafts in order to transmit 7.5 kW at…

A: Given data: P=7.5 kWN=720 rpmτs=33 MPaσcruss=60 MPaτCI=15 MPa Need to determine the flange coupling…

Q: Design a bushed-pin type flexible coupling for connecting a motor shaft to a pump shaft for the…

Q: A flanged bolt coupling consists of six - in. steel bolts evenly spaced around a bolt circle of…

A: Since we only answer one question at a time, we will answer the first one. Please resubmit the…

Q: A winch pulls a 500# cart up a hill, as shown. The main shaft of the winch is shown below, simply…

Q: A solid steel shaft ABC with diameter d =40 mm is driven at A by a motor that transmits 75 kW to the…

Q: A hollow shaft has an inner diameter of 0.035 m and an outer diameter of 0.06 m. Compute for the…

Q: 6. Design a cast iron protective flange coupling to connect two shafts in order to transmit 7.5 kW…

Q: Determine the magnitude of the largest torque TA that may be applied at A.

A: For solution refer below images.

Q: 8. Design a shaft and flange for a Diesel engine in which protected type of flange coupling is to be…

Q: Two designs for a shaft are being considered. Both have an outside diameter of 60 m and are 800 mm…

Q: A flange coupling having six bolts on a pitch circle radius of 300 mm connects two hollow shafts…

Q: A steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 60 MPa…

Q: m. Design a cast Iron flange coupling for the shaft. The allowable stresses are Shear stress for the…

Q: Design a hallow shaft (Diameter and length) that develops 80 kW of power while rotating at a speed…

Q: Find the power that can be safely transmitted by a flange type shaft coupling, if it has four…

A: Write the given data. n=4R=50 mm=0.050 md=12.5 mm=0.0125 mτstud=86 MPa=86×106 PaN=3600 rpm

Q: Question-1(CLO 1,2) A hollow bronze shaft of 3 in. outer diameter and 2 in. inner diameter is…

A: Given: The composite shaft is which is fastened rigidly together at the end. The outer diameter of…

Q: Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The…

A: Given DataP=15kWN=1000 rpmTs=60MPaTbolt=25 MPa

Q: nsmitted power = 0.050 MW, speed 500 rpm, Modulus of Ela . , Modulus of Rigidity = 70 GPa, Ultimate…

Q: Q4. A flanged protective type coupling is required to transmit 50 kW at 2000 r.p.m.. Find: (a) Shaft…

A: a) To find: The shaft diameter. Given : The power transmitted is P=50 kW. The speed is N=2000 rpm.…

Q: A hollow aluminum propeller shaft, 30 ft. Iong with 15 in. outer diameter and an inner diameter…

Q: In a gearbox, a spur gear is mounted on a shaft at equal distances from two supporting bearings. The…

A: Given:Maximum power transmit, P=3 kWSpeed of shaft, N=3600 rpmGear contact angle, φ=20oPitch…

Q: A flanged bolt coupling consists of six 12.5 – mm steel bolts evenly spaced around a bolt circle 300…

Q: Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm…

A: outside diameter cannot be 70m when inside dater is 50 mm . hence, taking outside diameter as 70 mm…

Q: Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft…

Q: Solve the following problem Two designs for a shaft are being considered. Both have an outside…

A: Given: The outside diameter of the solid shaft is, D= 70 mm. The inside diamter of solid shaft is,…

Q: Q 3. Design a rigid flange coupling to transmit a torque of 250 N-m between two coaxial shafts. The…

A: Given data The permissible stresses are given below: Shear stress on shaft = 100 MPa Bearing or…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

100%

Design a rigid flange coupling to transmit a torque of 250N-m between two coaxial shafts. The shaft

is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the

flanges. The shafts are keyed to the flange hub. The permissible stresses are given below:

Shear stress on shaft =100MPa

Bearing or crushing stress on shaft =250MPa

Shear stress on keys =100MPa

Bearing stress on keys = 250MPa

Shearing stress on cast iron = 200Mpa

Shear stress on bolts =100MPa

Torque = 257N-m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa Answer in Word please
Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 55 MPa in the shafts and 23 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.
A mild steel shaft has to transmit 75 kW at 200 rpm. Design a cast Iron flange coupling for the shaft. The allowable stresses are Shear stress for the shaft and keys 40 N/mm²Shear stress for bolts = 28 N/mm²Shear stress for C.I. coupling = 20 N/mm² Take wearing stress as twice the shear stress value and number of bolts for coupling as 6.
The flange coupling for two shafts made of plain carbon steel to be   connected. The shafts transmitting a toque of 600 N-m. Assume the following   permissible stresses for the coupling components: Shaft — Permissible shear stress = 35 MPa Keys — Rectangular formed end sunk key having permissible compressive strength = 60 MPa Bolts — Six numbers made of steel having permissible shear stress = 28 MPa Pitch circle diameter of bolts = 1.6 × Diameter of shaft   1. diameter of shaft =44.36 2. Hub length =67.5 3. Hub diameter 90 mm Calculate: 2. thickness of flange; 3. Diameter of flange 4. Width of key 5. Thickness of key 5. Diameter of bolt; 6. Crashing stress in bolt
A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outsude diameter and 90 mm in inside diameter. If the allowable aring stress in the shafts and the bolts is 60 MPa, how many 10 mm diameter steel bolts must be used on a 200 mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 400 The shaft is mounted on two 400 400 270 250 210 640i ]640 100
x Question: The diameter of shaft used in the below design is 90 mm. Identical pulleys are used in the design with a radius of 160 mm. The forces acting on the system are defined as follow: F₁ = 1P kN; F₂ = 8P kN; F3 = 2P kN; F₁ = 6P kN; F5 = 4P kN; F = 7P kN. Employing the maximum shear stress theory, calculate the maximum permissible P for a safe design experience. L₁ = 1.4m; L₂ = 1.8 m; L3 = 1.4m; L4 = 1.6 m; allow = 75 MPa (allowable strength, σs) A F₁ F₂ L2 m F4 B 3 F6 Fs
The flange coupling for two shafts made of plain carbon steel to be connected. The shafts transmitting a toque of 600 N-m. Assume the following permissible stresses for the coupling components: Shaft — Permissible shear stress = 35 MPa Keys — Rectangular formed end sunk key having permissible compressive strength = 60 MPa Bolts — Six numbers made of steel having permissible shear stress = 28 MPa Pitch circle diameter of bolts = 1.6 × Diameter of shaft Calculate: 1. diameter of shaft; 2. Hub length 3. Hub diameter 2. thickness of flange; 3. Diameter of flange 4. Width of key 5. Thickness of key 5. Diameter of bolt; 6. Crashing stress in bolt
A keyed gears delivers a torque of 912.4 N-m thru its shaft of 63.5 mm outside diameter. If the key has thickness of 15.875 mm and width of 11.1125 mm, find the length of the key. Assume permissible stress value of 61.2 MPa for shear and tension at 99.8 MPa
A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has the following standard dimensions: b x h x l = 8 mm x 7 mm x 18 mm. Calculate the stresses.
Q2: A rectangular key is used to connect a gear on a shaft of d=50 mm. The shaft transmitting power at a maximum shear stress. The shaft is made of AISI 1040 CD steel and the key is made of AISI 1020 CD steel. Design the dimensions of the key. Take F.S =3.
2. The diameters of the solid shafts are: AB is 0.6 in, A B D BC is 0.75 in. and CD is 0.9 in. The applied torques are: TĄ = 400 in lb, Tg = 1200 in Ib, Tc = 500 in İb. Determine the maximum shear stress in each of the three shafts. TA TB Ans: TmaxAB = 9431 psi, TmarBC = 9658 psi, TmaxCD = 9082 psi Te Fixed to wall